Subscribe

7-mode to cDOT

I have a new netapp 2554 in 7-mode. NFS, FC, SnapRestore, FlexClone was necessary. Whether before implementation I thought not to transfer to me to cDOT? Whether costs? And whether there are step by step instructions as to make it?

 

us-netapp01> sysconfig -a
	NetApp Release 8.2.2P1 7-Mode: Wed Oct  8 00:00:44 PDT 2014
	System ID: 0536934478 (us-netapp01); partner ID: 0536929503 (us-netapp02)
	System Serial Number: 721527000190 (us-netapp01)
	System Rev: C1
	System Storage Configuration: Multi-Path HA
	System ACP Connectivity: Full Connectivity
	Backplane Part Number: DS424
	Backplane Rev: 
	Backplane Serial Number: BPJWX7904948603
	slot 0: System Board 1.7 GHz (System Board XIX C1)
                Model Name:         FAS2554
                Part Number:        111-01324
                Revision:           C1
                Serial Number:      031521000612
                BIOS version:       8.3.0
                Loader version:     4.3
                Processors:         4
                Processor ID:       0x106e4
                Microcode Version:  0x3
                Processor type:     Intel(R) Xeon(R) CPU           C3528  @ 1.73GHz
                Memory Size:        18432 MB
                Memory Attributes:  Hoisting
                                    Normal ECC
                NVMEM Size:         1280 MB of Main Memory Used
                CMOS RAM Status:    OK
                Controller:         A
	Service Processor           Status: Online
		Firmware Version:   2.2.3
		Mgmt MAC Address:   00:A0:98:86:10:D2
		Ethernet Link:      up, full duplex, auto-neg complete
		Using DHCP:         yes
	IPv4 configuration:
		IP Address:         unknown
		Netmask:            unknown
		Gateway:            unknown
	IPv6 configuration:         Disabled
	slot 0: Internal 10/100/1000 Ethernet Switch
		Firmware Version:   Version4 SB_XX Switch0 
		Wrench:             auto-1000t-fd-up
		Locked-wrench:      auto-1000t-fd-up
		Device Type:        88E6176
                        memory mapped I/O base 0x00000000dfd00000, size 0x80000
                        I/O base 0x0000000000002040, size 0x20
                        memory mapped I/O base 0x00000000dfe08000, size 0x4000
                        memory mapped I/O base 0x00000000dfd80000, size 0x80000
                        I/O base 0x0000000000002060, size 0x20
                        memory mapped I/O base 0x00000000dfe0c000, size 0x4000
	slot 0: Quad Gigabit Ethernet Controller 82580
		e0a MAC Address:    00:a0:98:86:10:ce (auto-1000t-fd-up)
		e0b MAC Address:    00:a0:98:86:10:cf (auto-1000t-fd-up)
		e0M MAC Address:    00:a0:98:86:10:d0 (auto-1000t-fd-up)
		e0P MAC Address:    00:a0:98:86:10:d1 (auto-1000t-fd-up)
		Device Type:	150E
		Firmware Version:   3.22, 0x80000101
                        memory mapped I/O base 0x00000000dfc00000, size 0x80000
                        I/O base 0x0000000000002000, size 0x20
                        memory mapped I/O base 0x00000000dfe00000, size 0x4000
                        memory mapped I/O base 0x00000000dfc80000, size 0x80000
                        I/O base 0x0000000000002020, size 0x20
                        memory mapped I/O base 0x00000000dfe04000, size 0x4000
	slot 0: 10G Ethernet Controller CNA EP 8324
		(Dual-port, QLogic CNA 8324(8362) rev. 2)
		e0c MAC Address:    00:a0:98:86:10:d4 (auto-10g_twinax-fd-up)
		e0d MAC Address:    00:a0:98:86:10:d5 (auto-10g_twinax-fd-up)
                Device Type:        EP8324N
                NIC Firmware rev:   5.4.10.0
                        prefetchable memory base 0xde800000, size 0x200000
                        prefetchable memory base 0xdf208000, size 0x2000
                        prefetchable memory base 0xdea00000, size 0x200000
                        prefetchable memory base 0xdf20a000, size 0x2000
	slot 0: Interconnect HBA:   Mellanox IB MT25204
		GUID: 0x100000a0988610ce	LID: 0x4	Remote LID: 0x5
		Firmware rev:		1.0.800
		Hardware rev:		160
		Command rev:		1
		Interconnect Port: 4x
                        memory mapped I/O base 0xdfa00000, size 0x100000
                        prefetchable memory base 0xde000000, size 0x800000
	slot 0: SAS Host Adapter 0a (PMC-Sierra PM8001 rev. C, SAS, <UP>)
		Firmware rev:       01.11.07.00
		Base WWN:           5:00a098:005eac1:b0
		Phy State:          [0] Enabled, 6.0 Gb/s
		                    [1] Enabled, 6.0 Gb/s
		                    [2] Enabled, 6.0 Gb/s
		                    [3] Enabled, 6.0 Gb/s
                00.0 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300541)
                00.1 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300611)
                00.2 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300616)
                00.3 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300594)
                00.4 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7AJGX)
                00.5 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G4P9MX)
                00.6 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7611X)
                00.7 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7AN0X)
                00.8 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G76J7X)
                00.9 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6P9PX)
                00.10: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G798VX)
                00.11: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6T1TX)
                00.12: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7AN1X)
                00.13: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6MJHX)
                00.14: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G75TLX)
                00.15: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G1EZMX)
                00.16: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6MD6X)
                00.17: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6S57X)
                00.18: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6M9RX)
                00.19: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7647X)
                00.20: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7455X)
                00.21: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G73DGX)
                00.22: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7ADGX)
                00.23: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6U1MV)
		Shelf 0: DS4246E  Firmware rev. IOM6E A: 0153  IOM6E B: 0153
	slot 0: SAS Host Adapter 0b (PMC-Sierra PM8001 rev. C, SAS, <UP>)
		Firmware rev:       01.11.07.00
		Base WWN:           5:00a098:005eac1:b4
		Phy State:          [4] Enabled, 6.0 Gb/s
		                    [5] Enabled, 6.0 Gb/s
		                    [6] Enabled, 6.0 Gb/s
		                    [7] Enabled, 6.0 Gb/s
		QSFP Vendor:        Molex Inc.      
		QSFP Part Number:   112-00176+A0    
		QSFP Type:          Passive Copper 0.5m ID:00
		QSFP Serial Number: 505420529
                00.0 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300541)
                00.1 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300611)
                00.2 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300616)
                00.3 : NETAPP   X575_S1633400AMD NA00 381.3GB 520B/sect (S20KNYAG300594)
                00.4 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7AJGX)
                00.5 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G4P9MX)
                00.6 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7611X)
                00.7 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7AN0X)
                00.8 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G76J7X)
                00.9 : NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6P9PX)
                00.10: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G798VX)
                00.11: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6T1TX)
                00.12: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7AN1X)
                00.13: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6MJHX)
                00.14: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G75TLX)
                00.15: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G1EZMX)
                00.16: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6MD6X)
                00.17: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6S57X)
                00.18: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6M9RX)
                00.19: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7647X)
                00.20: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7455X)
                00.21: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G73DGX)
                00.22: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G7ADGX)
                00.23: NETAPP   X306_HMRKP02TSSM NA00 1695.4GB 512B/sect (P5G6U1MV)
		Shelf 0: DS4246E  Firmware rev. IOM6E A: 0153  IOM6E B: 0153
                        memory mapped I/O base 0xdfb30000, size 0x10000
                        memory mapped I/O base 0xdfb20000, size 0x10000
                        memory mapped I/O base 0x00000000dfb10000, size 0x10000
                        memory mapped I/O base 0x00000000dfb00000, size 0x10000
        slot 0: Fibre Channel Target Host Adapter 0c
                (QLogic CNA 8324 (8362) rev. 2, <LINK NOT CONNECTED>)
                Firmware rev:      7.2.0
                Flash rev:         2.1.0 
                Host Port Addr:    000000
                FC Nodename:       50:0a:09:80:80:f0:e4:df (500a098080f0e4df)
                FC Portname:       50:0a:09:81:80:f0:e4:df (500a098180f0e4df)
                Connection:        No link
                Switch Port:       Unknown
                SFP Vendor Name:   CISCO-TYCO
		SFP Vendor P/N:    1-2053783-2
		SFP Vendor Rev:    T
		SFP Serial No.:    TED1913B40W
		SFP Connector:     Passive Copper
		SFP Capabilities:  10 Gbit/Sec
                        prefetchable memory base 0xdf20c000, size 0x2000
                        prefetchable memory base 0xdf200000, size 0x4000
                        prefetchable memory base 0xdf000000, size 0x100000
        slot 0: Fibre Channel Target Host Adapter 0d
                (QLogic CNA 8324 (8362) rev. 2, <LINK NOT CONNECTED>)
                Firmware rev:      7.2.0
                Flash rev:         2.1.0 
                Host Port Addr:    000000
                FC Nodename:       50:0a:09:80:80:f0:e4:df (500a098080f0e4df)
                FC Portname:       50:0a:09:82:80:f0:e4:df (500a098280f0e4df)
                Connection:        No link
                Switch Port:       Unknown
                SFP Vendor Name:   CISCO-TYCO
		SFP Vendor P/N:    1-2053783-2
		SFP Vendor Rev:    T
		SFP Serial No.:    TED1913B45S
		SFP Connector:     Passive Copper
		SFP Capabilities:  10 Gbit/Sec
                        prefetchable memory base 0xdf20e000, size 0x2000
                        prefetchable memory base 0xdf204000, size 0x4000
                        prefetchable memory base 0xdf100000, size 0x100000
        slot 0: Fibre Channel Target Host Adapter 0e
                (QLogic 8324 (8362) rev. 2, <LINK NOT CONNECTED>)
                Firmware rev:      7.2.0
                Flash rev:         2.1.0 
                Host Port Addr:    000000
                FC Nodename:       50:0a:09:80:80:f0:e4:df (500a098080f0e4df)
                FC Portname:       50:0a:09:83:80:f0:e4:df (500a098380f0e4df)
                Connection:        No link
                Switch Port:       Unknown
                SFP Vendor Name:   FINISAR CORP.
		SFP Vendor P/N:    FTLF8528P3BNV-N1
		SFP Vendor Rev:    A
		SFP Serial No.:    NS50PUV
		SFP Connector:     LC
		SFP Capabilities:  2, 4, 8 Gbit/Sec
                        prefetchable memory base 0xdf508000, size 0x2000
                        prefetchable memory base 0xdf500000, size 0x4000
                        prefetchable memory base 0xdf300000, size 0x100000
        slot 0: Fibre Channel Target Host Adapter 0f
                (QLogic 8324 (8362) rev. 2, <LINK NOT CONNECTED>)
                Firmware rev:      7.2.0
                Flash rev:         2.1.0 
                Host Port Addr:    000000
                FC Nodename:       50:0a:09:80:80:f0:e4:df (500a098080f0e4df)
                FC Portname:       50:0a:09:84:80:f0:e4:df (500a098480f0e4df)
                Connection:        No link
                Switch Port:       Unknown
                SFP Vendor Name:   FINISAR CORP.
		SFP Vendor P/N:    FTLF8528P3BNV-N1
		SFP Vendor Rev:    A
		SFP Serial No.:    NS41CBH
		SFP Connector:     LC
		SFP Capabilities:  2, 4, 8 Gbit/Sec
                        prefetchable memory base 0xdf50a000, size 0x2000
                        prefetchable memory base 0xdf504000, size 0x4000
                        prefetchable memory base 0xdf400000, size 0x100000
	slot 0: Intel USB EHCI Adapter u0a (0xdf701000)
		boot0	Micron Technology 0x655, class 0/0, rev 2.00/11.10, addr 2 1936MB 512B/sect (10F0022700080469)
                        memory-mapped I/O base 0xdf701000, size 0x00000400

Re: 7-mode to cDOT

 

avichakov -

 

You'd need to talk with your account team about any cost to convert your licensing over to C-Mode.

 

All the documentation to re-install as a Cluster Mode system is on the mysupport.netapp.com site.

 

If it were my choice on a brand new installl, then I'd rather go forward with Clustered ONTAP.


I hope this response has been helpful to you.

At your service,

Eugene E. Kashpureff, Sr.
Independent NetApp Consultant http://www.linkedin.com/in/eugenekashpureff
Senior NetApp Instructor, IT Learning Solutions http://sg.itls.asia/netapp
(P.S. I appreciate 'kudos' on any helpful posts.)

 

Re: 7-mode to cDOT

 

my name is Chriz Ott, I'm working with NetApp as a Principal Architect for Transition.

 

 
 
 
 
 
P.S. if you feel this post is useful, please KUDO or “accept as a solution" so other people may find it faster.

Re: 7-mode to cDOT

Hi Avinchakov!

When you do transition this sytem to cDOT, be sure to use version 8.3 or later.  ONTAP 8.3 had some storage efficiency enhancements for the 2500 series that can increase your usable storage by 50% compared to version 8.2.

 

Jeff Asher

Principal Architect

Re: 7-mode to cDOT

avinchakov, 

 

Yes, 8.3 has Advanced Drive Partitioning or ADP is perhaps one of the most significant features of Clustered DataONTAP 8.3 (perhaps Flash performance might be as well). Why? Because it will dramatically affect the usable space for entry level and extreme performance systems.

 

Where it comes with Disk Slicing, Can compare the storage efficiency as below with Disk Slicing (DS) and without.

 

552700_orig.png