Community

Subscribe
Highlighted
Accepted Solution

FAS 3140 not show new disk after add new shelf DS4243

Hi,

I recently add new shelf's DS4243 at stack no my netapp FAS3140, after a i add the shelf, i run the following command's on filer.

sasadmin expander_map 
sasadmin shelf 
storage show disk -p

sasadmin expander_map

Expanders on channel 2a:

Level  1: WWN 50050cc10332d7bf, ID  0, Serial Number ' SHX0954292H138H', Product 'DS424IOM3       ', Rev '0131', Slot B

Level  2: WWN 50050cc103b1637f, ID  1, Serial Number ' SHX0954292H1K4B', Product 'DS424IOM3       ', Rev '0131', Slot B

Level  3: WWN 50050cc1039d25ff, ID  2, Serial Number ' SHX0954292H1KHA', Product 'DS424IOM3       ', Rev '0131', Slot B

Level  4: WWN 50050cc103b456bf, ID  3, Serial Number ' SHX0954293H1L4X', Product 'DS424IOM3       ', Rev '0131', Slot B

Level  5: WWN 50050cc104e397bf, ID  7, Serial Number ' SHJHU00000101B8', Product 'DS424IOM3       ', Rev '0160', Slot A

Level  6: WWN 50050cc104e48b7f, ID  5, Serial Number ' SHJHU00000101E5', Product 'DS424IOM3       ', Rev '0160', Slot A

Level  7: WWN 50050cc104e3037f, ID  4, Serial Number ' SHJHU00000101D8', Product 'DS424IOM3       ', Rev '0160', Slot A

sasadmin shelf

Expanders on channel 2a:

     +-------------------+

   0 |  0 |  1 |  2 |  3 |

     |  4 |  5 |  6 |  7 |

     |  8 |  9 | 10 | 11 |

     | 12 | 13 | 14 | 15 |

     | 16 | 17 | 18 | 19 |

     | 20 | 21 | 22 | 23 |

     +-------------------+

     +-------------------+

   1 |  0 |  1 |  2 |  3 |

     |  4 |  5 |  6 |  7 |

     |  8 |  9 | 10 | 11 |

     | 12 | 13 | 14 | 15 |

     | 16 | 17 | 18 | 19 |

     | 20 | 21 | 22 | 23 |

     +-------------------+

     +-------------------+

   2 |  0 |  1 |  2 |  3 |

     |  4 |  5 |  6 |  7 |

     |  8 |  9 | 10 | 11 |

     | 12 | 13 | 14 | 15 |

     | 16 | 17 | 18 | 19 |

     | 20 | 21 | 22 | 23 |

     +-------------------+

     +-------------------+

   3 |  0 |  1 |  2 |  3 |

     |  4 |  5 |  6 |  7 |

     |  8 |  9 | 10 | 11 |

     | 12 | 13 | 14 | 15 |

     | 16 | 17 | 18 | 19 |

     | 20 | 21 | 22 | 23 |

     +-------------------+

     +-------------------+

   7 |  0 |  1 |  2 |  3 |

     |  4 |  5 |  6 |  7 |

     |  8 |  9 | 10 | 11 |

     | 12 | 13 | 14 | 15 |

     | 16 | 17 | 18 | 19 |

     | 20 | 21 | 22 | 23 |

     +-------------------+

     +-------------------+

   5 |  0 |  1 |  2 |  3 |

     |  4 |  5 |  6 |  7 |

     |  8 |  9 | 10 | 11 |

     | 12 | 13 | 14 | 15 |

     | 16 | 17 | 18 | 19 |

     | 20 | 21 | 22 | 23 |

     +-------------------+

     +-------------------+

   4 |  0 |  1 |  2 |  3 |

     |  4 |  5 |  6 |  7 |

     |  8 |  9 | 10 | 11 |

     | 12 | 13 | 14 | 15 |

     | 16 | 17 | 18 | 19 |

     | 20 | 21 | 22 | 23 |

     +-------------------+

The new shelf's is number 4, 5 and 7.

But when i try to add the new disk's to filer i have the following message

disk show -n

disk show: No disks match option -n.

Please help how to solve this problem.

Regards

Re: FAS 3140 not show new disk after add new shelf DS4243

its been already added to filer spare disk pool , Pls check in spare disk list.

Re: FAS 3140 not show new disk after add new shelf DS4243

Do you see disks with "disk show -v"? Are they unowned?

Re: FAS 3140 not show new disk after add new shelf DS4243

disk show -n is for listing unowned disks. Youe disks are already owned by you filer and assigned to one of the pools. Spare pool most probably.

Re: FAS 3140 not show new disk after add new shelf DS4243

Hi when i execute "disk show -v" the filer show disks not have the owner, but assign to Pool0

2a.07.13               (2015678276)    Pool0  WD-WCAY01509004                 (2015678276)

2a.07.10               (2015678276)    Pool0  WD-WCAY01510472                 (2015678276)

2a.07.19               (2015678276)    Pool0  WD-WCAY01527067                 (2015678276)

2a.07.6                (2015678276)    Pool0  WD-WCAY01512076                 (2015678276)

2a.07.12               (2015678276)    Pool0  WD-WCAY01516608                 (2015678276)

2a.07.1                (2015678276)    Pool0  WD-WCAY01512111                 (2015678276)

2a.07.11               (2015678276)    Pool0  WD-WCAY01526039                 (2015678276)

2a.07.17               (2015678276)    Pool0  WD-WCAY01510473                 (2015678276)

2a.07.2                (2015678276)    Pool0  WD-WCAY01525675                 (2015678276)

2a.07.4                (2015678276)    Pool0  WD-WCAY01512401                 (2015678276)

2a.07.22               (2015678276)    Pool0  WD-WCAY01527721                 (2015678276)

2a.07.7                (2015678276)    Pool0  WD-WCAY01524282                 (2015678276)

2a.07.15               (2015678276)    Pool0  WD-WCAY01527203                 (2015678276)

2a.07.20               (2015678276)    Pool0  WD-WCAY01514282                 (2015678276)

2a.07.18               (2015678276)    Pool0  WD-WCAY01525405                 (2015678276)

2a.07.21               (2015678276)    Pool0  WD-WCAY01520371                 (2015678276)

2a.07.14               (2015678276)    Pool0  WD-WCAY01514082                 (2015678276)

2a.07.9                (2015678276)    Pool0  WD-WCAY01530403                 (2015678276)

2a.07.23               (2015678276)    Pool0  WD-WCAY01512093                 (2015678276)

2a.07.16               (2015678276)    Pool0  WD-WCAY01517181                 (2015678276)

2a.07.8                (2015678276)    Pool0  WD-WCAY01509515                 (2015678276)

2a.07.5                (2015678276)    Pool0  WD-WCAY01514388                 (2015678276)

2a.07.0                (2015678276)    Pool0  WD-WCAY01514100                 (2015678276)

2a.07.3                (2015678276)    Pool0  WD-WCAY01520766                 (2015678276)

 

At the Netapp SystemManager, disk appear with state present.

Re: FAS 3140 not show new disk after add new shelf DS4243

Since <disk show -n > gives output <disk show: No disks match option -n> and command < disk show -v > lists all disks with owner serial number (2015678276) , all disks have been assigned to the controller with serial number (2015678276).

You must have executed disk assign -n  -o <controller> after adding the new shelves.

The new disks are certainly owned by your controller.

Re: FAS 3140 not show new disk after add new shelf DS4243

But i cant create new aggregate, because i haven't disk to add aggregate because the new disk's not available.

Please can clarify if the shelf's ID must be sequential??? Because my shelfs is not sequential.

Regards.

Re: FAS 3140 not show new disk after add new shelf DS4243

There is no need for shelf id's to be sequential. The shelf ID's should be unique. But it will certainly be tidy in case they are sequential but not necessary.

Could you list all the steps/commands you've done after hot adding the disk shelves?

Re: FAS 3140 not show new disk after add new shelf DS4243

After i adding the shelf's i do the following commands:

sasadmin expander_map

sasadmin shelf

storage show disk -p

Re: FAS 3140 not show new disk after add new shelf DS4243

Is it system I'd of your filer or partner? If not, shelf was used by other filer in the past. You will need to manually assign disks using force option. Be sure to double check!