Network and Storage Protocols

How to configure UTA ports

avinchakov
8,512 Views

Hello,

I have FAS2554, I want to use 2 UTA ports for 10GB (I connect to Cisco) and 2 UTA ports for 8 GB FC. How they are configured? How to me to set up NFS on 10GB?

slot 0: Fibre Channel Target Host Adapter 0c
                (QLogic 8324 (8362) rev. 2, <OFFLINED BY USER/SYSTEM>)
                Firmware rev:      7.2.0
                Flash rev:         2.1.0 
                Host Port Addr:    000000
                FC Nodename:       50:0a:09:80:80:f0:e4:df (500a098080f0e4df)
                FC Portname:       50:0a:09:81:80:f0:e4:df (500a098180f0e4df)
                Connection:        No link
                Switch Port:       Unknown
                SFP Vendor Name:   CISCO-TYCO (Warning: SFP info not updated when port is OFFLINE)
		SFP Vendor P/N:    1-2053783-2
		SFP Vendor Rev:    T
		SFP Serial No.:    TED1913B40W
		SFP Connector:     Passive Copper
		SFP Capabilities:  10 Gbit/Sec
                        prefetchable memory base 0xdf208000, size 0x2000
                        prefetchable memory base 0xdf200000, size 0x4000
                        prefetchable memory base 0xdf000000, size 0x100000
        slot 0: Fibre Channel Target Host Adapter 0d
                (QLogic 8324 (8362) rev. 2, <OFFLINED BY USER/SYSTEM>)
                Firmware rev:      7.2.0
                Flash rev:         2.1.0 
                Host Port Addr:    000000
                FC Nodename:       50:0a:09:80:80:f0:e4:df (500a098080f0e4df)
                FC Portname:       50:0a:09:82:80:f0:e4:df (500a098280f0e4df)
                Connection:        No link
                Switch Port:       Unknown
                SFP Vendor Name:   CISCO-TYCO (Warning: SFP info not updated when port is OFFLINE)
		SFP Vendor P/N:    1-2053783-2
		SFP Vendor Rev:    T
		SFP Serial No.:    TED1913B45S
		SFP Connector:     Passive Copper
		SFP Capabilities:  10 Gbit/Sec
                        prefetchable memory base 0xdf20a000, size 0x2000
                        prefetchable memory base 0xdf204000, size 0x4000
                        prefetchable memory base 0xdf100000, size 0x100000
1 ACCEPTED SOLUTION

scottgelb
8,499 Views

For 7-Mode.... note that port pairs must be the same... so a/b either cna or fc and c/d the same.

 

ucadmin show

ucadmin modify -m fc|cna -t target|initiator -f portname

ucadmin show

 

If cDOT (except maintenance mode use 7-Mode commands above)

system node unified connect show | modify

View solution in original post

4 REPLIES 4

scottgelb
8,500 Views

For 7-Mode.... note that port pairs must be the same... so a/b either cna or fc and c/d the same.

 

ucadmin show

ucadmin modify -m fc|cna -t target|initiator -f portname

ucadmin show

 

If cDOT (except maintenance mode use 7-Mode commands above)

system node unified connect show | modify

scottgelb
8,498 Views

and reboot required to set the personality.

avinchakov
8,493 Views

Thank I will try it

avinchakov
8,484 Views

It works!

Public