topic Re: I get a errorcode not described in the manual [scf-00066] in Data Protection https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36544#M2452 <HTML><HEAD></HEAD><BODY><P>SC couldnt get backup progress from DFM which could be communications issue or something with DFM.</P><P></P><P>I recommend setting RUN_PM_BACKUP=N to avoid this until it is figured out why this is happening.</P><P></P><P>I have never seen this issue personally so my guess is communications related. What version of SC and also what other messages do you see? There should be some ZAPI messages? Zou can look and see what API SC sent to PM and see what came back, this is in debug output.</P><P></P><P>Keith</P></BODY></HTML> Wed, 02 Jan 2013 12:53:25 GMT ktenzer 2013-01-02T12:53:25Z I get a errorcode not described in the manual [scf-00066] https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36539#M2451 <HTML><HEAD></HEAD><BODY><P>What is this error?</P><P></P><P>[Tue Jan&nbsp; 1 04:01:40 2013] [scf-00066] Protection Manager backup progress next for job-id 873638 failed! Exiting at /&lt;/r3bd1db/soe3/opt/snapdb2-2.5/scServer3.6.0/snapcreator&gt;SnapCreator/DFM/PM.pm line 584.</P><P></P><P></P><P>Regards Magnus</P></BODY></HTML> Thu, 05 Jun 2025 06:13:02 GMT https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36539#M2451 magnus_nyvall 2025-06-05T06:13:02Z Re: I get a errorcode not described in the manual [scf-00066] https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36544#M2452 <HTML><HEAD></HEAD><BODY><P>SC couldnt get backup progress from DFM which could be communications issue or something with DFM.</P><P></P><P>I recommend setting RUN_PM_BACKUP=N to avoid this until it is figured out why this is happening.</P><P></P><P>I have never seen this issue personally so my guess is communications related. What version of SC and also what other messages do you see? There should be some ZAPI messages? Zou can look and see what API SC sent to PM and see what came back, this is in debug output.</P><P></P><P>Keith</P></BODY></HTML> Wed, 02 Jan 2013 12:53:25 GMT https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36544#M2452 ktenzer 2013-01-02T12:53:25Z Re: I get a errorcode not described in the manual [scf-00066] https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36550#M2453 <HTML><HEAD></HEAD><BODY><P>Our DFM serer was terribly overloaded and it took to long time for it to respond.</P><P>We are now trying to fix that issue.</P><P></P><P>We are a bit worried it can be because we now have quite a lot of datasets. (Closing in on 500)</P><P></P><P>Regards Magnus</P></BODY></HTML> Fri, 11 Jan 2013 07:54:09 GMT https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36550#M2453 magnus_nyvall 2013-01-11T07:54:09Z Re: I get a errorcode not described in the manual [scf-00066] https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36554#M2454 <HTML><HEAD></HEAD><BODY><P>Hi Magnus</P><P></P><P>We have had the same Issue after upgrade SC from 3.5 to 3.6 (Oncommand 5.0.0.7636). We don't find a solution, so we have to go to 3.5 again. Since the downgrade</P><P> it works without any Issue (few Months). Something has changed between 3.5 and 3.6. In near future (When I have a timeslot) i will open a Case about that. When I find a solution with support, i will inform you too...</P><P><A href="https://community.netapp.com/thread/23803" target="_blank"> Thread Link : 23803</A></P><P></P><P>regards </P><P>Thomas</P></BODY></HTML> Fri, 11 Jan 2013 08:53:44 GMT https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36554#M2454 brauntvr2swiss 2013-01-11T08:53:44Z Re: I get a errorcode not described in the manual [scf-00066] https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36557#M2455 <HTML><HEAD></HEAD><BODY><P>We dont get the "cannot connect to socket" problem.</P><P>We had an old hardware running DFM v4.02D12.</P><P></P><P>We have now upgraded to 5.1 on a new hardware and this problem is gone.</P><P></P><P>Regards Magnus</P></BODY></HTML> Mon, 21 Jan 2013 08:56:01 GMT https://community.netapp.com/t5/Data-Protection/I-get-a-errorcode-not-described-in-the-manual-scf-00066/m-p/36557#M2455 magnus_nyvall 2013-01-21T08:56:01Z