topic Re: DS14MK2 AT-FCx on FAS2020 in ONTAP Hardware

DS14MK2 AT-FCx on FAS2020

ademuynck — Thu, 05 Jun 2025 06:19:11 GMT

Hi everybody,

One of my customer want to add a DS14MK2 AT-FCx on his FAS2020 mono controler.

So i have installed this shelf, but i have a problem when i try to see this shelf ...

In my syslog message i have this error :

[scsi.cmd.notReadyCondition:notice]: Disk device 0b.17: Device returns not yet ready: CDB 0x12: Sense Data SCSI:not ready - Drive spinning up (0x2 - 0x4 0x1 0x0)(7712).

And when i watch in Filer View, under Storage, Shelves, Report, i have this ligne :

UNUSED.shelf0 UNUSED 0 - online n/a

So i have no idea why it didn't work ....

Thanks a lot for your advises

Regards.

Arnaud

Re: DS14MK2 AT-FCx on FAS2020

ogra — Tue, 11 Sep 2012 10:48:43 GMT

Hi Amaud,

Which Data ONTAP version are you running ?

Also, what is the capacity of SATA drive you want to add ?

As such there is no issue with the Drive spin.

You just need to make sure the Disk Shelf you are adding ( having minimum version of Data ONTAP) to the controller is having the correct Data ONTAP version. ( Atleast running the minimum version of Data ONTAP supported by the shelf).

Regards,

-Bakshana

Re: DS14MK2 AT-FCx on FAS2020

aborzenkov — Tue, 11 Sep 2012 10:49:55 GMT

Please show “storage show disk -x” output.

Re: DS14MK2 AT-FCx on FAS2020

ademuynck — Tue, 11 Sep 2012 12:03:16 GMT

Hi Bakshana,

I am running Data ONTAP 7.3.7. I try to add 6 disk of 1 Tb.

How can i check Data ONTAP version on the shelf ?

Thanks a lot

Re: DS14MK2 AT-FCx on FAS2020

ademuynck — Tue, 11 Sep 2012 12:07:26 GMT

Hi aborzenkov,

Here output of "storage show disk -x" command :

Disk i try to add, are :

-0a.xx and 0b xxx

Regards.

Re: DS14MK2 AT-FCx on FAS2020

aborzenkov — Tue, 11 Sep 2012 12:09:49 GMT

As far as I can tell it looks fine. So what is the problem (and message is not a problem by itself)?

Re: DS14MK2 AT-FCx on FAS2020

ademuynck — Tue, 11 Sep 2012 12:28:30 GMT

Problem is that i can't add any new disk to a new aggregate.

In fact, when i try to create new aggregate, no disk are available. I should have my 6 disk of 1Tb ?

so, is this line is normal ?

And when i watch in Filer View, under Storage, Shelves, Report, i have this ligne :

UNUSED.shelf0 UNUSED 0 - online n/a

shelf appear like UNUSED ?

Re: DS14MK2 AT-FCx on FAS2020

aborzenkov — Tue, 11 Sep 2012 12:30:14 GMT

Please, paste output of command “disk show -v”

Re: DS14MK2 AT-FCx on FAS2020

ademuynck — Tue, 11 Sep 2012 12:44:32 GMT

Hi.

Below output of "disk show -v" :

Owner of this disk appear to be FAS3020 ! The problem is i have no FAS3020 ... Only my FAS2020...

Re: DS14MK2 AT-FCx on FAS2020

aborzenkov — Tue, 11 Sep 2012 12:47:40 GMT

You will need to reassign disks. Try “disk assign 0a.16 -f”.

Re: DS14MK2 AT-FCx on FAS2020

ademuynck — Tue, 11 Sep 2012 13:13:31 GMT

Hi,

You rocks !!! It work fine now. so can you explain me why disk have been assign to a virtual FAS3020 ? It is strange no ?

Thanks a lot !

Re: DS14MK2 AT-FCx on FAS2020

scottgelb — Tue, 11 Sep 2012 14:33:00 GMT

Where did these disks come from? Sometimes a customer may ship from another system or a used shelf was purchased. Not likely a new factory shelf which would have no ownership.

Re: DS14MK2 AT-FCx on FAS2020

ademuynck — Tue, 11 Sep 2012 14:36:52 GMT

I am asking to my customer where did these disk come from ... I think this disk come from an older plateform FAS3020 ...