topic Netapp 2020 setup in ONTAP Hardware

Netapp 2020 setup

ESTADMIN1 — Thu, 05 Jun 2025 06:43:03 GMT

So, I'm trying to setup the 2020, I current have RAID6 using 4 disks each off each controller. I'm trying to add 1 more disk to a raid/aggregate, but I dont see how in the GUI(there is a spot, but it doesnt see the spare disks) and I dont see any disk command in the cli. Thanks in advance!

Name:	aggr0
Type:	Aggregate	Root Aggregate?
Status:	online,raid_dp	Raid Size:	16
Used Capacity:	233 GB	Checksums:	block
% Used:	98%
Total Capacity:	239 GB	Number of Disks:	3
Number of Files:	191
Max Files:	31.1 k	Double Parity?

	aggr0 (online,raid_dp, 98% used of 239 GB)
		/aggr0/plex0 (online)
		/aggr0/plex0/rg0 (3 disks,Disk Scrub: stopped, Last Scrub: Sun Oct 23 02:18:13 GMT 2011)
		0c.00.1 ( Type: dparity, Used: 266G, Serial No: 6SJ20CV40000N145LCSW
		Primary Port: SA:A Secondary Name: -, Secondary Port: -)
		0c.00.3 ( Type: parity, Used: 266G, Serial No: 6SJ20CWV0000N145LCU2
		Primary Port: SA:A Secondary Name: -, Secondary Port: -)
		0c.00.5 ( Type: data, Used: 266G, Serial No: 6SJ20CY70000N145JN4W
		Primary Port: SA:A Secondary Name: -, Secondary Port: -)

Disk	Type	Checksum Compatibility	Shelf	Bay	Chan	Used	Physical	Pool	Aggregate
0c.00.0	partner	zoned/block	0	0	SA:A	0 MB	274 GB	Pool0
0c.00.1	dparity	zoned/block	0	1	SA:A	266 GB	274 GB	Pool0	aggr0
0c.00.2	partner	zoned/block	0	2	SA:A	0 MB	274 GB	Pool0
0c.00.3	parity	zoned/block	0	3	SA:A	266 GB	274 GB	Pool0	aggr0
0c.00.4	partner	zoned/block	0	4	SA:A	0 MB	274 GB	Pool0
0c.00.5	data	zoned/block	0	5	SA:A	266 GB	274 GB	Pool0	aggr0
0c.00.6	partner	zoned/block	0	6	SA:A	0 MB	274 GB	Pool0
0c.00.7	spare	zoned/block	0	7	SA:A	266 GB	274 GB	Pool0
0c.00.8	unowned	--	--	--	--	--	--	--	--
0c.00.9	unowned	--	--	--	--	--	--	--	--
0c.00.10	unowned	--	--	--	--	--	--	--	--
0c.00.11	unowned	--	--	--	--	--	--	--	--

Netapp 2020 setup

scottgelb — Sun, 23 Oct 2011 20:21:41 GMT

disks are unowned... use "disk assign xx.xx.xx" to assign a disk to a node... or assign 2 to one node then "disk assign all" if you want to assign the 4 unowned evenly between both nodes...then you can add the drive. From the cli "aggr add aggrname 1"... although if data is on the aggr you could hit some performance constraints while the single disk is written to unless you run reallocate.

Netapp 2020 setup

ESTADMIN1 — Mon, 24 Oct 2011 17:06:32 GMT

Thanks for the reply, I've tried using the disk command in the cli. Both commands disk and aggr when entered int othe cli report unknown command. This is in both admin and advance.

bmc shell*-> ?

exit Exit shell (or press ^D)

battery show Display firmware battery information

battery flash Re-flash battery firmware

battery verify Verify battery firmware

bmc config Display BMC configuration

bmc config autoneg [enabled|disabled] Enable/Disable ethernet port auto negotiation

bmc config dhcp [on|off] Set BMC dhcp

bmc config duplex [full|half] Set ethernet port duplex mode

bmc config gateway [gateway] Set BMC IP Gateway

bmc config ipaddr [ip-address] Set BMC IP Address

bmc config netmask [netmask] Set BMC IP Netmask

bmc config speed [10|100] Set ethernet port speed at 10M or 100M

bmc show Show BMC version and system information

echo [string] Print [string] to the console

events all Print all system events

events clear Delete all events

events info Print SEL(system event log) information

events latest [N] Print N latest system events

events oldest [N] Print N oldest system events

events search [attr=N] Search for events by attribute/value pair

events show [N] Print event N

fru show Show chassis FRU data

priv Show current privilege level

priv set Return to admin privilege

priv set admin Enter admin privilege

priv set advanced Enter advanced privilege

sensors search [attr=N] Display a sensor by attribute

sensors show Display current state of sensors

service info Show active BMC network services

system console Return to the system console

system core Dump system core

system log Show the system console history

system power cycle Power cycle controller

system power off Power off controller

system power on Power on controller

system power status Display Power Status

system reset Reset controller

system reset backup Reset controller with backup firmware

system reset primary Reset controller with primary firmware

system show Show system information

Re: Netapp 2020 setup

scottgelb — Mon, 24 Oct 2011 17:13:28 GMT

You are in the bmc. To Getty knap... If ontap is running type "system console"

Sent from my iPhone 4S

Re: Netapp 2020 setup

scottgelb — Mon, 24 Oct 2011 18:38:30 GMT

autocorrect on my iPhone makes me laugh...still adjusting... to GET TO ONTAP... system console