topic Re: FAS2040 Automatic shutdown sequence cancelled in ONTAP Hardware

FAS2040 Automatic shutdown sequence cancelled

hwaltari01 — Wed, 04 Jun 2025 15:09:00 GMT

My out-of-support FAS2040 says exactly once a hour "monitor.shutdown.cancel:warning]: Automatic shutdown sequence cancelled". No other messages are printed on neither console nor message -logfile. Only the other head does this, other head does not. Outputs of 'system health' and environment -commands do not reveal anything.

Obviously an automatic shutdown is cancelled, but what causes the shutdown and why it is cancelled?

Any indication of where to look is appreciated.

Re: FAS2040 Automatic shutdown sequence cancelled

ekashpureff — Thu, 27 Apr 2017 11:51:23 GMT

hwaltari -

The place to look is the syslog translator tool:

http://mysupport.netapp.com/eservice/ems

Unfortunately it doesn't say much about this message.

I hope this response has been helpful to you.

At your service,

Eugene E. Kashpureff, Sr.
Independent NetApp Consultant http://www.linkedin.com/in/eugenekashpureff
Senior NetApp Instructor, FastLane US http://www.fastlaneus.com/
(P.S. I appreciate 'kudos' on any helpful posts.)

Re: FAS2040 Automatic shutdown sequence cancelled

AlexDawson — Fri, 28 Apr 2017 02:28:51 GMT

Can you please run "ups status" on the system to see if it may have been configured for a UPS at some point?

Re: FAS2040 Automatic shutdown sequence cancelled

hwaltari01 — Fri, 28 Apr 2017 06:38:35 GMT

Alex,

Thanks for your suggestion.

I got reply "'ups' commands not supported"

And if my memory serves me right it has not been never implemented, either.

Please note that the version is 8.1.4 7-Mode

Re: FAS2040 Automatic shutdown sequence cancelled

AlexDawson — Fri, 28 Apr 2017 08:40:04 GMT

Thanks - just wanted to quickly check that.

Can you connect to the BMC and run "sensors show" and provide the output? and "environment status" from ONTAP.

Re: FAS2040 Automatic shutdown sequence cancelled

hwaltari01 — Fri, 28 Apr 2017 11:50:31 GMT

Alex,

Please see the attachments

Re: FAS2040 Automatic shutdown sequence cancelled

AlexDawson — Fri, 28 Apr 2017 14:17:45 GMT

This all looks fine.

Do you know when it started? Is it HA or a single controller, and is it logged on both controllers or just one?

My guess is a system sensors problem that asserts and then clears. Going through similar cases (this message on a FAS2040), it can happen after a power supply is replaced, or turned off and then on again - shutting the system down completely, removing power, then restarting it can resolve it in some cases, but in others a new system board is required.

If you wish to post the contents of /etc/messages over an hour - so between when two warnings come up - may help narrow it down. Or may not - and even if it does, the solution is the same - restart, then replace system board if problems persist. Remember that all attachments are publicly viewable, so you may wish to remove or censor some information.

Re: FAS2040 Automatic shutdown sequence cancelled

hwaltari01 — Tue, 02 May 2017 06:00:27 GMT

Alex,

This is a HA-pair, and the other controller does not produce the message. And frankly I do not have any idea when this has started. The filer is about to be decommissioned, just waiting for the last projects to cool down.

I'll try the shutdown-remove power units-restart -sequence.

Heres a fresh snippet of the messages

Tue May 2 06:20:32 EEST [dmnetapp1-2:monitor.shutdown.cancel:warning]: Automatic shutdown sequence cancelled
Tue May 2 07:00:00 EEST [dmnetapp1-2:kern.uptime.filer:info]: 7:00am up 934 days, 18:54 993035249 NFS ops, 69966330 CIFS ops, 0 HTTP ops, 0 FCP ops, 0 iSCSI ops
Tue May 2 07:20:32 EEST [dmnetapp1-2:monitor.shutdown.cancel:warning]: Automatic shutdown sequence cancelled
Tue May 2 08:00:00 EEST [dmnetapp1-2:kern.uptime.filer:info]: 8:00am up 934 days, 19:54 993035249 NFS ops, 69966474 CIFS ops, 0 HTTP ops, 0 FCP ops, 0 iSCSI ops
Tue May 2 08:20:32 EEST [dmnetapp1-2:monitor.shutdown.cancel:warning]: Automatic shutdown sequence cancelled

Re: FAS2040 Automatic shutdown sequence cancelled

AlexDawson — Tue, 02 May 2017 06:28:05 GMT

Sounds like a good plan.