https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108602#M7901 <P>Thank I will try it</P> Thu, 13 Aug 2015 18:53:07 GMT avinchakov 2015-08-13T18:53:07Z https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108598#M7898 <P>Hello,</P><P>I have FAS2554, I want to use 2 UTA ports for 10GB (I connect to Cisco) and 2 UTA ports for 8 GB FC. How they are configured? How to me to set up NFS on 10GB?</P><PRE>slot 0: Fibre Channel Target Host Adapter 0c (QLogic 8324 (8362) rev. 2, &lt;OFFLINED BY USER/SYSTEM&gt;) Firmware rev: 7.2.0 Flash rev: 2.1.0 Host Port Addr: 000000 FC Nodename: 50:0a:09:80:80:f0:e4:df (500a098080f0e4df) FC Portname: 50:0a:09:81:80:f0:e4:df (500a098180f0e4df) Connection: No link Switch Port: Unknown SFP Vendor Name: CISCO-TYCO (Warning: SFP info not updated when port is OFFLINE) SFP Vendor P/N: 1-2053783-2 SFP Vendor Rev: T SFP Serial No.: TED1913B40W SFP Connector: Passive Copper SFP Capabilities: 10 Gbit/Sec prefetchable memory base 0xdf208000, size 0x2000 prefetchable memory base 0xdf200000, size 0x4000 prefetchable memory base 0xdf000000, size 0x100000 slot 0: Fibre Channel Target Host Adapter 0d (QLogic 8324 (8362) rev. 2, &lt;OFFLINED BY USER/SYSTEM&gt;) Firmware rev: 7.2.0 Flash rev: 2.1.0 Host Port Addr: 000000 FC Nodename: 50:0a:09:80:80:f0:e4:df (500a098080f0e4df) FC Portname: 50:0a:09:82:80:f0:e4:df (500a098280f0e4df) Connection: No link Switch Port: Unknown SFP Vendor Name: CISCO-TYCO (Warning: SFP info not updated when port is OFFLINE) SFP Vendor P/N: 1-2053783-2 SFP Vendor Rev: T SFP Serial No.: TED1913B45S SFP Connector: Passive Copper SFP Capabilities: 10 Gbit/Sec prefetchable memory base 0xdf20a000, size 0x2000 prefetchable memory base 0xdf204000, size 0x4000 prefetchable memory base 0xdf100000, size 0x100000</PRE> Wed, 04 Jun 2025 23:32:09 GMT https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108598#M7898 avinchakov 2025-06-04T23:32:09Z https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108599#M7899 <P>For 7-Mode.... note that port pairs must be the same... so a/b either cna or fc and c/d the same.</P><P>&nbsp;</P><P>ucadmin show</P><P>ucadmin modify -m fc|cna -t target|initiator -f portname</P><P>ucadmin show</P><P>&nbsp;</P><P>If cDOT (except maintenance mode use 7-Mode commands above)</P><P>system node unified connect show | modify</P> Thu, 13 Aug 2015 18:34:10 GMT https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108599#M7899 scottgelb 2015-08-13T18:34:10Z https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108600#M7900 <P>and reboot required to set the personality.</P> Thu, 13 Aug 2015 18:34:25 GMT https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108600#M7900 scottgelb 2015-08-13T18:34:25Z https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108602#M7901 <P>Thank I will try it</P> Thu, 13 Aug 2015 18:53:07 GMT https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108602#M7901 avinchakov 2015-08-13T18:53:07Z https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108603#M7902 <P>It works!</P> Thu, 13 Aug 2015 19:03:32 GMT https://community.netapp.com/t5/Network-and-Storage-Protocols/How-to-configure-UTA-ports/m-p/108603#M7902 avinchakov 2015-08-13T19:03:32Z