Cannot Access Fas2050 using Netapp System Manager

careukadm — Thu, 05 Jun 2025 07:09:39 GMT

Hello,

I'm trying to manage our filers (fas2050) using the Netapp System Manager. When I add the discovered devices and try and login I get the following error -

API invoke failed. The remote server returned an error: (502) Bad Gateway

I'm on the same subnet as the filer

Any ideas?

Thanks

Re: Cannot Access Fas2050 using Netapp System Manager

sinhaa — Tue, 31 Aug 2010 08:43:36 GMT

Looking into your problem.

Can you provide the following information:

1. you filer ONTAP version. your System Manager version.

2.output of the command "route -sn" on your filer.

3. output of command "ifconfig -a" on filer cli.

4. Output of the command "ipconfig /all" from from Windows server where System manager is installed.

Try pinging the filer from you Windows system ( which has system manager install) using the full hostname and IP.

Re: Cannot Access Fas2050 using Netapp System Manager

careukadm — Tue, 31 Aug 2010 09:58:19 GMT

Looking into your problem.

Can you provide the following information:

1. you filer ONTAP version. your System Manager version - 7.3.3.

2.output of the command "route -sn" on your filer. -

Routing tables

Internet:
Destination      Gateway            Flags     Refs     Use Interface
default          10.254.253.1       UGS         4     2733 vif1
10.254.253/24    link#5             UC          0        0 vif1
10.254.253.1     0:0:c:7:ac:0       UHL         1        0 vif1
10.254.253.10    0:10:db:ff:20:50   UHL         0        0 vif1
10.254.253.84    0:c:29:b7:c9:78    UHL         0      285 vif1
10.254.253.90    link#5             UHL         1     3713 vif1
10.254.253.100   0:17:8:50:b4:b0    UHL         1      443 vif1
10.254.253.101   0:50:56:b8:5f:45   UHL         0       26 vif1
10.254.253.112   0:c:29:1a:24:7     UHL         0      124 vif1
10.254.253.135   2:a0:98:24:85:68   UHL         0      483 lo
10.254.253.255   ff:ff:ff:ff:ff:ff UHL         0     2435 vif1
127              127.0.0.1          UGS         0      290 lo
127.0.0.1        127.0.0.1          UH          2       52 lo

3. output of command "ifconfig -a" on filer cli.

e0a: flags=0xad48867<UP,BROADCAST,RUNNING,MULTICAST,TCPCKSUM> mtu 1500
        ether 02:a0:98:24:85:68 (auto-1000t-fd-up) flowcontrol full
        trunked vif1
e0b: flags=0xad48867<UP,BROADCAST,RUNNING,MULTICAST,TCPCKSUM> mtu 1500
        ether 02:a0:98:24:85:68 (auto-1000t-fd-up) flowcontrol full
        trunked vif1
lo: flags=0x1948049<UP,LOOPBACK,RUNNING,MULTICAST,TCPCKSUM> mtu 8160
        inet 127.0.0.1 netmask-or-prefix 0xff000000 broadcast 127.0.0.1
        ether 00:00:00:00:00:00 (VIA Provider)
vif1: flags=0x22d48863<UP,BROADCAST,RUNNING,MULTICAST,TCPCKSUM> mtu 1500
        inet 10.254.253.135 netmask-or-prefix 0xffffff00 broadcast 10.254.253.25
5
        partner vif1 (not in use)
        ether 02:a0:98:24:85:68 (Enabled virtual interface)

4. Output of the command "ipconfig /all" from from Windows server where System manager is installed.

Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 10.254.253.84
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 10.254.253.1
DHCP Server . . . . . . . . . . . : 10.254.253.100
DNS Servers . . . . . . . . . . . : 10.254.253.100
10.0.0.10

Try pinging the filer from you Windows system ( which has system manager install) using the full hostname and IP.

Yes, both work.

One thing the fqdn of the filers in the NSM is 'hostname.hostname' rather than 'hostname.domainname' not sure if that is the reason??

topic Re: Cannot Access Fas2050 using Netapp System Manager in Active IQ Unified Manager Discussions

Cannot Access Fas2050 using Netapp System Manager

Re: Cannot Access Fas2050 using Netapp System Manager

Re: Cannot Access Fas2050 using Netapp System Manager