Hi,
>>> As I am using WFA2.1: Could there be an error introduced with 2.1 regarding invoke-nassh in a workflow?
I tried a version of your command using code as follows through a workflow and seems to work fine for me. This was on WFA 2.1.
Command code I tried was:
------------------------
Param (
[parameter(Mandatory=$true, HelpMessage="Array name or IP address")]
[string]$Array,
[parameter(Mandatory=$true, HelpMessage="Name of the volume for which the reallocate should be set up.")]
[string]$VolumeName,
[parameter(Mandatory=$false, HelpMessage="This threshold marks the defragmentation count for which reallocate should start. Default is 4")]
[ValidateRange(3,10)]
[int]$Threshold = 4,
[parameter(Mandatory=$false, HelpMessage="Reallocate Job Schedule: Minute (Valid values are from -1 to 59 with -1 meaning all possible values.)")]
[ValidateRange(-1,59)]
[int]$Minute = 8,
[parameter(Mandatory=$false, HelpMessage="Reallocate Job Schedule: Hour (Valid values are from -1 to 23 with -1 meaning all possible values.)")]
[ValidateRange(-1,23)]
[int]$Hour = 2,
[parameter(Mandatory=$false, HelpMessage="Reallocate Job Schedule: Day of month (Valid values are from -1 to 31 with -1 or 0 meaning all possible values.)")]
[ValidateRange(-1,31)]
[int]$DayOfMonth = -1,
[parameter(Mandatory=$false, HelpMessage="Reallocate Job Schedule: Day of week (Valid values are from -1 to 6 with -1 meaning all possible values.)")]
[ValidateRange(-1,6)]
[int]$DayOfWeek = 6
)
#--- connect to controller
Connect-WfaController -Array $Array
#--- vars
$msg = $VolumeName + ": "
#--- Checks (and exits if checks fail)
$vol = Get-NaVol -Names $VolumeName -ErrorAction Stop
$volpath = "/vol/" + $vol.name
$reallocstatus = Get-NaReallocate -ErrorAction Stop
if($reallocstatus -match "Reallocation [a-z ]* on$") {
Get-WFALogger -Info -message $($msg + "Reallocation is already enabled on the storage system.")
} else {
Get-WFALogger -Info -message $($msg + "Reallocation not yet enabled on the storage system -> enabling.")
Enable-NaReallocate -ErrorAction Stop
}
if($Minute -lt 0) {
$schedule = "*"
} else {
$schedule = [string]$Minute
}
if($Hour -lt 0) {
$schedule += " *"
} else {
$schedule += " " + [string]$Hour
}
if($DayOfMonth -lt 1) {
$schedule += " *"
} else {
$schedule += " " + [string]$DayOfMonth
}
if($DayOfWeek -lt 0) {
$schedule += " *"
} else {
$schedule += " " + [string]$DayOfWeek
}
if($schedule -eq "* * * *"){
throw $msg + "The schedule '" + $schedule + "' is not allowed."
}
#--- Configure the reallocate scan for the volume
$cmd = "reallocate start -t " + $Threshold + " -p " + $volpath
Invoke-NaSSH -Command $cmd -ErrorAction Stop
# Invoke-WfaCli -CliCommand $cmd
Get-WFALogger -Info -message $($msg + "Scheduling the job: " + $schedule)
Set-NaReallocateSchedule -Path $volpath -Schedule $schedule -ErrorAction Stop
-------------
filer_prompt*> reallocate status -v
Reallocation scans are on
/vol/xyz:
State: Idle
Flags: whole_vol,maybe_realloc,repeat,keep_vvbn
Threshold: 4
Schedule: 4 3 * 2
Interval: n/a
Optimization: 1
-------------
If it still fails for you can you also paste the workflow details (command parameters sent) or the workflow DAR file.
Thanks,
Shailaja
