ONTAP Discussions

7-mtt and Ontap 9.2

drutten57
12,168 Views

Is there a known date when the next 7mtt will be released were A200 and Ontap 9.2 is supported?

 

Does anyone know if it's possible to manually add "support" for 9.2 and A200 in some conf-file in 7-mtt or is it hardcoded just to anger evryone?

 

The manual for 7-mtt only states mimumum ontap-release. Everytime a version is statet it follows by "or later". Well 9.2 is a later version.

 

interopmatrix does not have 9.2 listed for 7-mtt.

 

 

12 REPLIES 12

SeanHatfield
11,776 Views

Possible, yes.  Work with your NetApp SE to file a PVR, to qualify your transition scenario and obtain those instructions.

 

 

If this post resolved your issue, help others by selecting ACCEPT AS SOLUTION or adding a KUDO.

ChristianSmet
11,637 Views

Hi Sean,

 

is there any possibility we might get an updated 7mtt version?

We are implementing new systems with the intention of using DOT9.2 with a vfiler to SVM migration.

 

br,

Chritstian

drutten57
11,631 Views

Sean, That would take rather long time.. So, we did i manually instead.

 

Christian!

From what I've heard, the next relase will be available anytime now, with support for 9.2. Middle, late september...

 

Btw, long time no see 😃

 

Best Regards,

Tobias

ChristianSmet
11,628 Views

Thanks 🙂

I agree ... PVR isn't something you should step into for this.

Waiting some weeks should be possible.

It would even be better if I could disable the DOT verification somewhere in the tool.

 

At the moment it's just ontap simulators that are setup to test.

todd_shawcross
11,380 Views

Add the following line to end of the file: <7MTT-dir>/etc/conf/transition-tool.conf 

 

clustered.ontap.versions.supported= 9.2.0

 

Once this line is added, restart 7-Mode Transition Tool service.

 

This will override the version check failed error

djpm
10,551 Views

I've been trying to change the conf file so it supports 9.3 using the same syntax but no luck.

 

Does anybody have any other suggestions or know when a newer version 7mtt is planned for?

 

Thanks in advance!

andxtz
10,376 Views

Hi,

 

If you upgrade first to 7mtt 3.3 and then you modify the config file, it works. You can add the 9.3 system into 7mtt but i did not yet test a migration.

 

 

djpm
10,368 Views

Cheers for that.

 

I've added and it works! Also completed a test migration without issue.

pjmagallon
9,607 Views

Hi, I have the same problem with DATAONTAP 9.3P1, I have included the line "clustered.ontap.versions.supported= 9.3.0" and it doesn't work.

 

Once this line is added, restart 7-Mode Transition Tool service (v3.3).

 

Please, any idea ? Thanks.

drutten57
8,382 Views

@pjmagallon wrote:

Hi, I have the same problem with DATAONTAP 9.3P1, I have included the line "clustered.ontap.versions.supported= 9.3.0" and it doesn't work.

 

Once this line is added, restart 7-Mode Transition Tool service (v3.3).

 

Please, any idea ? Thanks.


Hi,

 

It works fine for me with both 9.3P1 and 9.3P2

 

I've only added

 

clustered.ontap.versions.supported=9.3.0

 

in the end of the transition-tool.conf file.

pjmagallon
8,370 Views

OK, we have tried it again, and now it's working.

 

Thanks.

JMPNETAPP
7,982 Views

You have to inlcude the patch version.

Example:

"clustered.ontap.versions.supported= 9.3P1"

Public