ONTAP Discussions

Migration aggregate and volumes to other NetApp

Bronkz
7,889 Views

Hello,

I have a NetApp with 7-mode 8.2.1 and I need to migrate aggregate on vfiler and all volumes with this aggregate to other NetApp. Is it possible to copy all non-distruptive? If no, Could You please write other solution step by step ?

1 ACCEPTED SOLUTION

NAYABSK
7,853 Views

So i should understand that you have same or more space as same as the source controller at the destination controller  ??

 

In that case i would suggest a copy method or best option to go with snapmirror 

 

1) Create as same agrregate structure in the destination as same as source ( Including volumes )

 

2) Create a snapmirror relation and initiate the transfer........

 

 

Thanks

Nayab

View solution in original post

7 REPLIES 7

NAYABSK
7,860 Views

Hi,

 

 

May i know if you are going to migrate with HA-Pair or across to other controller in a different HA-pair ?

 

 

If this is within a HA-Pair then follow the below procedure 

 

 

Now let us assume i have two controller filerA & filerB and i am moving aggregate from A to B 

 

 

 

Change options (both controllers):

 

options disk.auto_assign off

 

options autosupport.enable off

 

options httpd.enable.access on (for disk refresh)

 

Verify Volume Status:

 

vol status –s

 

Verify Disks

 

filer> disk show <disks>

 

Offline Volumes

 

filera> vol offline

 

Offline Aggregates

 

filera> aggr offline <aggr>

 

filera> aggr offline <aggr>

 

Note current disk ownership/IDs:

 

Removing ownership of the disks:

 

filera> priv set advanced

 

filera*> disk remove_ownership <disks>

 

Verify Disk Ownership (not owned):

 

filera> disk show –n

 

filera> options disk.auto_assign on

 

On the controller filerB

 

Change disk auto assign:

 

options disk.auto_assign off

 

Verify Disk Ownership (not owned):

 

filerb> disk show –n

 

Take ownership of the disks

 

priv set advanced

filerb*> disk assign 0b.22 0b.23 –s <filerb serial#>

 

Verify Disk Ownership (all visible disks)

filerb> disk show –v

 

Verify disks correctly assigned

filerb> aggr status –r / aggr status –s

 

Online Aggregate

 

filerb> aggr online <disks>

 

filerb> aggr online <disks>

 

Change options back:

 

options disk.auto_assign on

 

options autosupport.enable on

 

options httpd.enable.access off (for disk refresh)

 

 

Thanks,

Nayab

 

 

***If my reply helped to solve the issue, please help to mark it as solution so that it would be helpful to other with same issue****

OmSrivastava
6,549 Views

Hi, 

 

I want to move just few volumes to the other controller (HA Pair ) having version 8.2.4 .  What would be the requirements for volumes (offline/online/flexclone etc. ) . Could you please help me with both ways CLI and DFM .

 

Many thanks in Advance !!!

OmSrivastava
6,547 Views

Please reply with full procedure.

 

Thanks!!

Bronkz
7,855 Views

Hello,

NetApps are out of HA-pair.

NAYABSK
7,854 Views

So i should understand that you have same or more space as same as the source controller at the destination controller  ??

 

In that case i would suggest a copy method or best option to go with snapmirror 

 

1) Create as same agrregate structure in the destination as same as source ( Including volumes )

 

2) Create a snapmirror relation and initiate the transfer........

 

 

Thanks

Nayab

Bronkz
7,845 Views

Yes, I have a free space on destination. Ok I will try to use Snapmirror. Thank you for understanding.

NAYABSK
7,837 Views

Sure, Let me know if you have any doubts further 

 

 

Thanks,

Nayab

Public