EF & E-Series, SANtricity, and Related Plug-ins

E series storage factory default

joeczczcz
48,234 Views

Hi all,

we have E2724 in our demo pool available for partners. Storage is returned to us with changed management IP and storage password assigned often. Is there some procedure to quickly reset controllers to factory default state?

Thx in advance

Josef

15 REPLIES 15

penelope
47,802 Views

Josef

here are the command line parameters

Command line 10.x

clear storageArray configuration [all | volumeGroups]

 

Command line 11.x

set storageArray resetConfiguration=true;

Penelope Carr

NetApp

resqme914
47,804 Views

Your best bet might be to set up an in-band management station to which you will cable the returned hardware to.  You would have to invest in the appropriate HBA for your management station, though.

joeczczcz
47,801 Views

Thx you both, but this does not work if you have password stored in controller or if access LUN is deleted. First I need to clear password and then setup new IP address. I can do it using serial port, but not on NetApp, because lack of documentation... Sun (Oracle) and IBM has this well documented. Unfortunately on Netapp box those steps not working. What commands I can use in VxWorks shell to reset password and set IP?  NetCfgShow, netCfgSet are useless.

penelope
47,801 Views

I know it is a little late in replying but did you ever get this fixed?

ALOVELL222
47,803 Views

I am curious about this as well. I have E2624 with LSI HBA controllers. LSI was no help, they refered me here. There is a Service Interface available through the serial port. I don't believe the password is a configurable, set at the factory by the manufacturer, and this is where i need to go inorder to reset the management IP addresses to DHCP. This interface would be very similar to Dell PowerVault MD3000, but the passwords are specific to the manufacturer. Any thoughts on what the NetApp password might be?

penelope
47,800 Views

Here are the default settings for the serial port, they are not configurable.  This port is generally used by NetApp when troubleshooting the systems.

 

login name ******

password ********

 

If you require anything else please let me know.

 

Re: E series storage factory default

Penelope “Penny” Carr

NetApp Inc.

Advanced Consulting Services

josefdvoracek
47,675 Views

Hi Penelope, the login/password is really just stars or it was censored by forum?

 

thanks

mkinali
45,002 Views

Hello, 

 

I found this old topic. I have a question  regarding to service interface login?

 

What is the factory default password?

 

 

 

Press within 5 seconds: <S> for Service Interface, <BREAK> for baud rate
urrent date: 07/24/14  time: 20:15:13

 

Enter Password to access Service Interface (60 sec timeout):
Password incorrect

 

Enter Password to access Service Interface (60 sec timeout):
SPRI Password input timed out

 SPRI login failed.

hariprak
44,936 Views

Hi,

 

Please raise a support ticket with NetApp.

 

Thanks

If this post resolved your issue, help others by selecting ACCEPT AS SOLUTION or adding a KUDO.

Josh_Kirkpatrick
29,410 Views

Hello. I am running into a similar problem on my E2760. I was doing a POC. We are done and ready to fully deploy. I grew in an enclosure and my SAN became degraded then eventually offline. My two controllers are showing "OE LF" and "OE LU".

I just want to reset my controllers to factory settings and re-configre. When I am console I only get lockout status. SMcli replies

"Unable to execute command as the controller is currently in lockdown mode.

Use the "show storageArray healthStatus" command for further information.
SMcli failed."

 

SM GUI reports the error that my database is corupt, and steps to fix it. But I can't manage the SAN from Gui because I can't get past the error.

 

Any assistance would be wonderful.

mcadena123
13,033 Views

Hi please share below you will make a lot of techs happy

What's the default user and login ?? eos-a :

Casma
28,185 Views

 E5500


-Startup a terminal emulation program like kitty
-Use Serial-Connection 9600, 8N1, NoFlow
-Type <Ctrl><PAUSE/BREAK> within kitty
-When prompted for input within 5 seconds, press <S> in UPPERCASE for the service interface menu.
-A prompt for the Service Interface password is displayed. Enter <SPRIentry>
-Change IP or Reset Admin-Password via Menu

AleRogozi
26,266 Views

going nuts with this - SPRIentry does not work as service password. reset button does nothing. anybody?

SkillVPS
26,146 Views

 to press <S> for Service Menu press <ESC> instead


##<Contact Support for login information>

 

Run the following commands on both controllers –

psvClearSodRebootLoopCounter

clearHardwareLockdown

lemClearLockdown


Then unplug ctrl-A and run the following commands on ctrl-B:

loadDebug

cmgrSetAltToFailed

cmgrSetAltToOptimal

 

https://dokumen.tips/documents/ds3500-lockdown-recovery.html

Public