Thanks, Aman,
My issue is connecting FAS8040 to only 1 DS4243. It seems hard to find the specified diagram, also after that I stuck in LOADER Mode. Below is the error message:
----------------------------
Starting AUTOBOOT press Ctrl-C to abort...
Loading X86_64/freebsd/image1/kernel:0x100000/7950592 0x895100/4206472 Entry at 0xffffffff80171230
Loading X86_64/freebsd/image1/platform.ko:0x1000000/1985879 0x11e5000/288800 0x122b820/272560
Starting program at 0xffffffff80171230
NetApp Data ONTAP 8.3
atkbd: unable to get the current command byte value.
create polling thread
Copyright (C) 1992-2015 NetApp.
All rights reserved.
Checking boot device filesystem
** /dev/da0s1
** Phase 1 - Read and Compare FATs
** Phase 2 - Check Cluster Chains
** Phase 3 - Checking Directories
** Phase 4 - Checking for Lost Files
65 files, 2311392 free (1626424 clusters)
MARK FILE SYSTEM CLEAN? yes
MARKING FILE SYSTEM CLEAN
Retry #1 of 5: /sbin/fsck_msdosfs /dev/da0s1
Retry #2 of 5: /sbin/fsck_msdosfs /dev/da0s1
Repaired boot device filesystem
*******************************
* *
* Press Ctrl-C for Boot Menu. *
* *
*******************************
Jul 28 04:40:01 Battery charge capacity: 3840 mA*hr. Power outage protection flash de-staging cycles: 57
ixgbe: e0c: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 10240)!
original max threads=40, original heap size=41943040
bip_nitro Virtual Size Limit=309182464 Bytes
bip_nitro: user memory=4134682624, actual max threads=236, actual heap size=247463936
ixgbe: e0d: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 10240)!
ixgbe: e0a: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 10240)!
ixgbe: e0b: ** JUMBOMBUF DEBUG ** switching to large buffers(9k -> 3k): (sz = 10240)!
qla_init_hw: CRBinit running ok: 8c633f
NIC FW version in flash: 5.4.9
qla_init_hw: CRBinit running ok: 8c633f
NIC FW version bundled: 5.4.51
Jul 28 04:41:11 [localhost:config.noPartnerDisks:CRITICAL]: No disks were detected for the partner; this node cannot perform takeover correctly.
WAFL CPLEDGER is enabled. Checklist = 0x7ff841ff
Jul 28 04:41:11 [localhost:callhome.dsk.config:warning]: Call home for DISK CONFIGURATION ERROR
Jul 28 04:41:13 [localhost:cf.fm.noMBDisksOrIc:warning]: Could not find the local mailbox disks. Could not determine the firmware state of the partner through the HA interconnect.
PANIC : raid: Unable to find root aggregate. Reason: Unknown. (DS=3, DL=3, DA=3, BDTOC=0, BDLBL=0, BLMAG=4 BLCRC=8, BLVER=0, BLSZ=0, BLTOC=0, BLOBJ=0)
version: 8.3: Mon Mar 9 19:20:57 PDT 2015
conf : x86_64.optimize
cpuid = 0
Uptime: 1m39s
PANIC: raid: Unable to find root aggregate. Reason: Unknown. (DS=3, DL=3, DA=3, BDTOC=0, BDLBL=0, BLMAG=4 BLCRC=8, BLVER=0, BLSZ=0, BLTOC=0, BLOBJ=0) in SK process rc on release 8.3 (C) on Tue Jul 28 04:41:13 GMT 2020
version: 8.3: Mon Mar 9 19:20:57 PDT 2015
compile flags: x86_64.optimize
Writing panic info to HA mailbox disks.
HA: current time (in sk_msecs) 34906 (in sk_cycles) 2802805569703
DUMPCORE: START
Dumping to disks: 0a.03.2
....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
DUMPCORE: END -- coredump written.
----------------
It could be the wrong cable connect as I guest.
Thanks,
Dang