Hello
I just finish new AFF a220 setup which is attached to our Cisco MDS 9148 to and I can not get a link between the two.
I've configured both sides of FC and matched the speed. (8Gb) I must be missing something in between that I can't figure out.
This is the setting/config for one of the connections SAN side:
Note : There is just something strange that the Physical Protocol: ethernet !!
CTRA::system*> fcp adapter show -instance -node CTRA-01
(network fcp adapter show)
Node: CTRA-01
Adapter: 0c
UUID:
Description: Fibre Channel Target Adapter 0c (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
Physical Protocol: ethernet
Maximum Speed: 10
Administrative Status: up
Operational Status: link not connected
Extended Status: ADAPTER UP
Host Port Address: 0
Firmware Revision: 8.9.0
Data Link Rate (Gbit): 0
Fabric Established: false
Fabric Name: -
Connection Established: loop
Is Connection Established: false
Mediatype: ptp
Configured Speed: auto
Data Protocols Supported: fcp
LIF Capable: true
THA Index: 2
Handle: 2
Physical Slot: 0
Original WWNN: 50:0a:09:80:0e:07:68:07
Adapter WWNN: 50:0a:09:80:80:43:46:b8
Adapter WWPN: 50:0a:09:83:80:43:46:b8
Queue Depth: 4096
Switch Port: :
Form Factor Of Transceiver: SFP
Vendor Name Of Transceiver: FINISAR CORP.
Part Number Of Transceiver: FTLF8528P3BCV-QL
Revision Of Transceiver: A
Serial Number Of Transceiver: NT230NA
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
Vendor OUI Of Transceiver: 00:90:65
Wavelength In Nanometers: 850
Date Code Of Transceiver: 15:01:12
Validity Of Transceiver: true
Connector Used: LC
Encoding Used: 8B10B
Is Internally Calibrated: true
Received Optical Power: 0.0 (uWatts)
Is Received Power In Range: false
SFP Transmitted Optical Power: 0.0 (uWatts)
Is Xmit Power In Range: false
Node: CTRA-01
Adapter: 0d
UUID:
Description: Fibre Channel Target Adapter 0d (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
Physical Protocol: ethernet
Maximum Speed: 10
Administrative Status: up
Operational Status: link not connected
Extended Status: ADAPTER UP
Host Port Address: 0
Firmware Revision: 8.9.0
Data Link Rate (Gbit): 0
Fabric Established: false
Fabric Name: -
Connection Established: loop
Is Connection Established: false
Mediatype: ptp
Configured Speed: auto
Data Protocols Supported: fcp
LIF Capable: true
THA Index: 3
Handle: 3
Physical Slot: 0
Original WWNN: 50:0a:09:81:0e:07:68:07
Adapter WWNN: 50:0a:09:80:80:43:46:b8
Adapter WWPN: 50:0a:09:84:80:43:46:b8
Queue Depth: 4096
Switch Port: :
Form Factor Of Transceiver: SFP
Vendor Name Of Transceiver: FINISAR CORP.
Part Number Of Transceiver: FTLF8528P3BCV-QL
Revision Of Transceiver: A
Serial Number Of Transceiver: NT21986
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
Vendor OUI Of Transceiver: 00:90:65
Wavelength In Nanometers: 850
Date Code Of Transceiver: 15:01:12
Validity Of Transceiver: true
Connector Used: LC
Encoding Used: 8B10B
Is Internally Calibrated: true
Received Optical Power: 0.0 (uWatts)
Is Received Power In Range: false
SFP Transmitted Optical Power: 0.0 (uWatts)
Is Xmit Power In Range: false
Node: CTRA-01
Adapter: 0e
UUID:
Description: Fibre Channel Target Adapter 0e (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
Physical Protocol: ethernet
Maximum Speed: 10
Administrative Status: up
Operational Status: link not connected
Extended Status: ADAPTER UP
Host Port Address: 0
Firmware Revision: 8.9.0
Data Link Rate (Gbit): 0
Fabric Established: false
Fabric Name: -
Connection Established: loop
Is Connection Established: false
Mediatype: ptp
Configured Speed: auto
Data Protocols Supported: fcp
LIF Capable: true
THA Index: 0
Handle: 0
Physical Slot: 0
Original WWNN: 50:0a:09:82:0e:07:68:07
Adapter WWNN: 50:0a:09:80:80:43:46:b8
Adapter WWPN: 50:0a:09:81:80:43:46:b8
Queue Depth: 4096
Switch Port: :
Form Factor Of Transceiver: SFP
Vendor Name Of Transceiver: FINISAR CORP.
Part Number Of Transceiver: FTLF8528P3BCV-QL
Revision Of Transceiver: A
Serial Number Of Transceiver: NSR2Q2T
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
Vendor OUI Of Transceiver: 00:90:65
Wavelength In Nanometers: 850
Date Code Of Transceiver: 14:12:26
Validity Of Transceiver: true
Connector Used: LC
Encoding Used: 8B10B
Is Internally Calibrated: true
Received Optical Power: 0.0 (uWatts)
Is Received Power In Range: false
SFP Transmitted Optical Power: 0.0 (uWatts)
Is Xmit Power In Range: false
Node: CTRA-01
Adapter: 0f
UUID:
Description: Fibre Channel Target Adapter 0f (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
Physical Protocol: ethernet
Maximum Speed: 10
Administrative Status: up
Operational Status: link not connected
Extended Status: ADAPTER UP
Host Port Address: 0
Firmware Revision: 8.9.0
Data Link Rate (Gbit): 0
Fabric Established: false
Fabric Name: -
Connection Established: loop
Is Connection Established: false
Mediatype: ptp
Configured Speed: auto
Data Protocols Supported: fcp
LIF Capable: true
THA Index: 1
Handle: 1
Physical Slot: 0
Original WWNN: 50:0a:09:83:0e:07:68:07
Adapter WWNN: 50:0a:09:80:80:43:46:b8
Adapter WWPN: 50:0a:09:82:80:43:46:b8
Queue Depth: 4096
Switch Port: :
Form Factor Of Transceiver: SFP
Vendor Name Of Transceiver: FINISAR CORP.
Part Number Of Transceiver: FTLF8528P3BCV-QL
Revision Of Transceiver: A
Serial Number Of Transceiver: NSR2G76
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
Vendor OUI Of Transceiver: 00:90:65
Wavelength In Nanometers: 850
Date Code Of Transceiver: 14:12:26
Validity Of Transceiver: true
Connector Used: LC
Encoding Used: 8B10B
Is Internally Calibrated: true
Received Optical Power: 0.0 (uWatts)
Is Received Power In Range: false
SFP Transmitted Optical Power: 0.0 (uWatts)
Is Xmit Power In Range: false
4 entries were displayed.