ONTAP Hardware

NVRAM size mismatch between nodes detected

SEIMTEXTER
5,656 Views

Hello,

 

I have a FAS2552 with each controller reporting this during boot.

 

Feb 15 15:10:57 [<arrayname>:nv.partner.size.mismatch:ALERT]: CF monitor: NVRAM size mismatch between nodes detected; node requires 661651456 bytes, partner exported 0 bytes.

 

Nodes are cabled correctly and it's just a 2-controller / no expansion switchless cluster running ONTAP 9.7.  Any ideas are welcome, but I need to get this fixed! 

 

Doesn't appear to be a bad NV DIMM -

 

2552::> system fru-check show
Node FRU Status
------------------ ---------------------------- -----------
2552-01
DIMM-1 pass
DIMM-NV1 pass
2552-02
DIMM-1 pass
DIMM-NV1 pass
BootMedia pass
PCIe Devices pass
6 entries were displayed.

What's going on here?

1 ACCEPTED SOLUTION

paul_stejskal
5,056 Views

I think it's normal. If one node is offline or powering up, the size will of course be different. I've always seen it and put it in the "that's normal output" category of my brain.

 

View solution in original post

11 REPLIES 11

hmoubara
5,611 Views

Hello,

 

Is the error mentioned only seen during boot?

Can you verify the health of the cluster:

 

>  system ha interconnect status show

> cluster show

 

Thanks

SEIMTEXTER
5,585 Views

yep, it's only during boot, and the array seems to be healthy otherwise.  Not sure if I should be concerned about it or just ignore it? 

 

> system ha interconnect status show

not sure where to run this.  it looks like ha can either expand out to hardware or halt, but is not valid by itself, at least at my runlevel (at the cluster(?) prompt)  Cdot is still pretty foreign to me, I mostly still work on 7-mode.

> cluster show

both nodes show true for health and true for eligibility, whatever that means, I assume it's good!

paul_stejskal
5,578 Views

What is the serial #? It may be good to open a case if you have entitlements.

SEIMTEXTER
5,576 Views

yeah we don't have entitlements or a support contract unfortunately.  Seems like it's working fine, it just spits that error out on boot ¯\_(ツ)_/¯

andris
5,567 Views

system ha interconnect status show is a privilege: advanced command.

::> set advanced

::*> system ha interconnect status show

navion
5,060 Views

Also getting several nv.partner.size.mismatch on every ONTAP update.

paul_stejskal
5,057 Views

I think it's normal. If one node is offline or powering up, the size will of course be different. I've always seen it and put it in the "that's normal output" category of my brain.

 

SEIMTEXTER
5,046 Views

I'm with you 100% on that.  we replaced the entire filer and the "error" persisted, but no visible alerts or performance issues related to that message.  Thanks everyone!

Mjizzini
5,606 Views

This could have happened during reboot while the interconnect was down.  

To verify the health of the interconnect, run  the command below.

::*>storage failover show -instance

 

If the interconnect link is fine, a takeover giveback should clear this issue.

navion
5,013 Views
According to KB:

Cause
The interconnect is temporarily link up and down.

Solution
No action is required as it is automatically restored.

SEIMTEXTER
5,008 Views

Thank you for that KB article, that's it exactly.  If someone who works for NetApp can expand the list of affected systems, that would probably help others find it faster.  Thanks again all.

Public