ONTAP Hardware

Netapp 2020 setup

ESTADMIN1
3,143 Views

So, I'm trying to setup the 2020,  I current have RAID6 using 4 disks each off each controller.  I'm trying to add 1 more disk to a raid/aggregate, but I dont see how in the GUI(there is a spot, but it doesnt see the spare disks) and I dont see any disk command in the cli. Thanks in advance!

Name:
aggr0

Type:
Aggregate
Root Aggregate?
/na_admin/images/check12x12white.gif
Status:
online,raid_dp
Raid Size:
16
Used Capacity:
233 GB
Checksums:
block
% Used:
98%

Total Capacity:
239 GB
Number of Disks:
3
Number of Files:
191

Max Files:
31.1 k
Double Parity?
/na_admin/images/check12x12white.gif


aggr0 (online,raid_dp, 98% used of 239 GB)


/aggr0/plex0 (online)




0c.00.1 ( Type: dparity,  Used: 266G, Serial No: 6SJ20CV40000N145LCSW


Primary Port: SA:A Secondary Name: -, Secondary Port: -)


0c.00.3 ( Type: parity,  Used: 266G, Serial No: 6SJ20CWV0000N145LCU2


Primary Port: SA:A Secondary Name: -, Secondary Port: -)


0c.00.5 ( Type: data,  Used: 266G, Serial No: 6SJ20CY70000N145JN4W


Primary Port: SA:A Secondary Name: -, Secondary Port: -)

  DiskTypeChecksum CompatibilityShelfBayChanUsedPhysicalPoolAggregate
0c.00.0partnerzoned/block00SA:A0 MB274 GBPool0
0c.00.1dparityzoned/block01SA:A266 GB274 GBPool0aggr0
0c.00.2partnerzoned/block02SA:A0 MB274 GBPool0
0c.00.3parityzoned/block03SA:A266 GB274 GBPool0aggr0
0c.00.4partnerzoned/block04SA:A0 MB274 GBPool0
0c.00.5datazoned/block05SA:A266 GB274 GBPool0aggr0
0c.00.6partnerzoned/block06SA:A0 MB274 GBPool0
0c.00.7sparezoned/block07SA:A266 GB274 GBPool0
0c.00.8unowned----------------
0c.00.9unowned----------------
0c.00.10unowned----------------
0c.00.11unowned----------------
4 REPLIES 4

scottgelb
3,143 Views

disks are unowned... use "disk assign xx.xx.xx" to assign a disk to a node... or assign 2 to one node then "disk assign all" if you want to assign the 4 unowned evenly between both nodes...then you can add the drive.  From the cli "aggr add aggrname 1"... although if data is on the aggr you could hit some performance constraints while the single disk is written to unless you run reallocate.

ESTADMIN1
3,143 Views

Thanks for the reply, I've tried using the disk command in the cli. Both commands disk and aggr when entered int othe cli report unknown command. This is in both admin and advance.

bmc shell*-> ?

exit                                  Exit shell (or press ^D)

battery show                          Display firmware battery information

battery flash                         Re-flash battery firmware

battery verify                        Verify battery firmware

bmc config                            Display BMC configuration

bmc config autoneg [enabled|disabled] Enable/Disable ethernet port auto negotiation

bmc config dhcp [on|off]              Set BMC dhcp

bmc config duplex [full|half]         Set ethernet port duplex mode

bmc config gateway [gateway]          Set BMC IP Gateway

bmc config ipaddr [ip-address]        Set BMC IP Address

bmc config netmask [netmask]          Set BMC IP Netmask

bmc config speed [10|100]             Set ethernet port speed at 10M or 100M

bmc show                              Show BMC version and system information

echo [string]                         Print [string] to the console

events all                            Print all system events

events clear                          Delete all events

events info                           Print SEL(system event log) information

events latest [N]                     Print N latest system events

events oldest [N]                     Print N oldest system events

events search [attr=N]                Search for events by attribute/value pair

events show [N]                       Print event N

fru show                              Show chassis FRU data

priv                                  Show current privilege level

priv set                              Return to admin privilege

priv set admin                        Enter admin privilege

priv set advanced                     Enter advanced privilege

sensors search [attr=N]               Display a sensor by attribute

sensors show                          Display current state of sensors

service info                          Show active BMC network services

system console                        Return to the system console

system core                           Dump system core

system log                            Show the system console history

system power cycle                    Power cycle controller

system power off                      Power off controller

system power on                       Power on controller

system power status                   Display Power Status

system reset                          Reset controller

system reset backup                   Reset controller with backup firmware

system reset primary                  Reset controller with primary firmware

system show                           Show system information

scottgelb
3,143 Views

You are in the bmc. To Getty knap... If ontap is running type "system console"

Sent from my iPhone 4S

scottgelb
3,143 Views

autocorrect on my iPhone makes me laugh...still adjusting... to GET TO ONTAP... system console

Public