Network and Storage Protocols
Network and Storage Protocols
Hi all,
First of all I am new to ontap. I have setup an single node cluster ASA-C250.
Ports e0c and e0d are used for the cluster interconnect network.
Ports e1a and e1b are connected to a Juniper switch. Now I want to configure a SVM with iSCSI as Access protocol. But for some reason I can the ports e1a,e1b . I have the same issue when I want to add thes ports to the Default Broadcast domain
dacs-cluster01::> network port broadcast-domain add-ports -ipspace Default -broadcast-domain Default -ports dacs-cluster01-01:e1a,dacs-cluster01-01:e1b,dacs-cluster01-02:e1a,dacs-cluster01-02:e1b
Error: command failed: can't find port
Extra info:
dacs-cluster01::> version
NetApp Release 9.15.1P3: Wed Sep 25 22:33:44 UTC 2024
dacs-cluster01::> network device-discovery show
Node/ Local Discovered
Protocol Port Device (LLDP: ChassisID) Interface Platform
----------- ------ ------------------------- ---------------- ----------------
dacs-cluster01-01/cdp
e0c dacs-cluster01-02 e0c ASA-C250
e0d dacs-cluster01-02 e0d ASA-C250
e1a dacs-cluster01-02 e1a ASA-C250
e1b dacs-cluster01-02 e1b ASA-C250
dacs-cluster01-01/lldp
e0M dacsswt001 (a4:0e:75:7e:96:cb)
40 -
e0c dacs-cluster01-02 (d0:39:ea:c2:e8:f1)
e0c -
e0d dacs-cluster01-02 (d0:39:ea:c2:e8:f1)
e0d -
e1a dacsswt003 (b4:16:78:a4:c4:40)
et-0/0/48 -
e1b dacsswt004 (b4:16:78:a4:f6:40)
et-0/0/48 -
dacs-cluster01-02/cdp
e0c dacs-cluster01-01 e0c ASA-C250
e0d dacs-cluster01-01 e0d ASA-C250
e1a dacs-cluster01-01 e1a ASA-C250
e1b dacs-cluster01-01 e1b ASA-C250
dacs-cluster01-02/lldp
e0M dacsswt001 (a4:0e:75:7e:96:cb)
90 -
e0c dacs-cluster01-01 (d0:39:ea:c2:eb:29)
e0c -
e0d dacs-cluster01-01 (d0:39:ea:c2:eb:29)
e0d -
e1a dacsswt003 (b4:16:78:a4:c4:40)
et-0/0/49 -
e1b dacsswt004 (b4:16:78:a4:f6:40)
et-0/0/49 -
18 entries were displayed.
dacs-cluster01::> system node run -node dacs-cluster01-01 sysconfig -a
<snip>
slot 1: Dual 100G Ethernet Controller CX6-Mezz
e1a MAC Address: d0:39:ea:5c:63:6a (auto-100g_sr4-fd-up)
QSFP Vendor: SOLID-OPTICS
QSFP Part Number: QSFP-100G-LR4-LC
QSFP Serial Number: SOZ131Lp3095
e1b MAC Address: d0:39:ea:5c:63:6b (auto-100g_sr4-fd-up)
QSFP Vendor: SOLID-OPTICS
QSFP Part Number: QSFP-100G-LR4-LC
QSFP Serial Number: SOZ131Lp3097
Device Type: CX6 PSID(NAP0000000013)
Firmware Version: 20.30.1004
Part Number: 111-04588
Hardware Revision: B0
Serial Number: 032422000999
Thanks in advance.
Carlo
Solved! See The Solution
According to Hardware Universe, an ASA C250, with an X1153 100GbE card, should be installed in slot 2....not slot 1. Slot 1 is reserved for an NVMe storage card. I would start here.
According to Hardware Universe, an ASA C250, with an X1153 100GbE card, should be installed in slot 2....not slot 1. Slot 1 is reserved for an NVMe storage card. I would start here.
The partnumber is 111-04588. According to the Hardware Universe there are 2 categories, Networking and NVMe storage. What’s the difference? We’re talking about the same card, so does that mean I can also use this type of card to connect to something else?
Hello, this card (X1153) can be used in slot 1 for attaching external storage such as an NS224 disk shelf; and/or it can be used in slot 2 for front-end 100GbE networking.
OK, thank you for your support. Tomorrow I’ll move the card to the other slot and let you know if that solves the issue.
Moving the card to slot 2 solved the problem. Thank you very much !!