Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I have HA-pair of FAS3140 controllers connected to 3 stacks. Four DS14-MK4-FC shelves (stack 1), three DS14-MK2-AT shelves (stack 2) and one DS4246 shelf (stack 3). I'm trying to gather controller to shelves cabling information and I'm stuck with a couple of questions:
1. "storage show shelf " shows only stack 1 and stack 3. "environ shelf" shows all 3 stacks. Why is stack 2 missing from "storage show shelf" output?
2. In multipathing configurations both controllers have access to a stack from two loops. But it's unclear if controller is connected to the first shelf IN port or the last shelf OUT port. I can extract FC port to IOM (A or B) cabling info from the "storage show shelf" output. But how do I now which module port (IN or OUT) FC port is connected to? Config Advisor isn't helpful here, because it doesn't show even the FC port to IOM mapping.
7 REPLIES 7
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Nikita,
You may wish to run 'Configuration Advisor' to double check the shelf cabling info.
Good luck
Henry
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Henry, thanks for stopping by. Let me draw your attention to one particular part of my initial post:
Config Advisor isn't helpful here, because it doesn't show even the FC port to IOM mapping.
Let me know if I'm missing something obvious here.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
There is no documented way to track cabling for FC shelves (and it is not clear whether such way even exists). For SAS you can track SFP serial numbers which gives you exact port-to-port connectivity.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
That's quite a surprise. Are you saying that the only way to determine how system is cabled is to go on-site and in case cables aren't marked, track them by hand?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Check the visualisation section of MyAutosupport which will show how the system is cabled.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Does it show IN/OUT IOM ports mapping?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
IOM is SAS and it is possible to reliably track.
Отправлено с iPhone
12.07.2013, в 8:23, "Nikita Andreev" <xdl-communities@communities.netapp.com<mailto:xdl-communities@communities.netapp.com>> написал(а):
<https://communities.netapp.com/index.jspa>
Re: Gathering Shelf Cabling Information
created by Nikita Andreev<https://communities.netapp.com/people/N.ANDREEV> in Data ONTAP - View the full discussion<https://communities.netapp.com/message/112918#112918>
Does it show IN/OUT IOM ports mapping?
Reply to this message by replying to this email -or- go to the message on NetApp Community<https://communities.netapp.com/message/112918#112918>
Start a new discussion in Data ONTAP by email<mailto:discussions-community-products_and_solutions-data_ontap@communities.netapp.com> or at NetApp Community<https://communities.netapp.com/choose-container.jspa?contentType=1&containerType=14&container=2877>