ONTAP Hardware

FAS 3240 / DS2246 configuration issue

CGandvfx

Hi everyone!

I recently bought a used Netapp FAS 3240 and an empty disk shelf DS2246 from eBay. I wanted to set it up from scratch to learn how to configure storage systems. I attached 6 drives of HUC109060css600 (600GB 10K SAS made for IBM). FAS 3240 is connected to DS2246 through QSFP-QSPF cable on 0a. I ran the systems for the first time and went through the option (4) Clean configuration and initialize all disks. Data ONTAP version is 8.0.5 7- mode. I got the error message " PANIC: ../driver/disk/disk.c:22047: Assertion failure. in SK process disk_admin". System is keep booting , then I select maintenance mode boot: below is the results of disk show and sysconfig -v  and aggr status commands

disk show -n
Local System ID: 2017636203

DISK OWNER POOL SERIAL NUMBER HOME
------------ ------------- ----- ------------- ----------- --
0a.30.4 Not Owned NONE KWHBY3DF
0a.30.3 Not Owned NONE KWHDX6YF
0a.30.5 Not Owned NONE KWHDX5VF
*> sysconfig ?
usage: sysconfig -v [ <slot> ]
*> Sat Feb 27 18:04:58 GMT [monitor.chassisPowerSupply.degraded:notice]: Chassis power supply 2 is degraded: PSU2 is over voltage
Sat Feb 27 18:04:58 GMT [monitor.chassisPowerSupply.degraded:notice]: Chassis power supply 2 is degraded: PSU2 has failed
Sat Feb 27 18:04:58 GMT [monitor.chassisPowerSupply.degraded:notice]: Chassis power supply 2 is degraded: PSU2 DC has failed
Sat Feb 27 18:04:58 GMT [monitor.chassisPowerSupply.degraded:notice]: Chassis power supply 2 is degraded: PSU2 Fan1 Speed is Critical Low (2700 RPM)
Sat Feb 27 18:04:58 GMT [callhome.chassis.ps.degraded:error]: Call home for CHASSIS POWER SUPPLY DEGRADED: PS 2
sysconfig -v
NetApp Release 8.0.5 7-Mode: Sun Jan 20 21:53:54 PST 2013
System ID: 2017636203 ()
System Serial Number: 940001065843 ()
System Rev: H7
System Storage Configuration: Single Path
System ACP Connectivity: NA
slot 0: System Board 2.3 GHz (System Board XVI H7)
Model Name: FAS3240
Part Number: 111-00692
Revision: H7
Serial Number: 9438943791
BIOS version: 5.2.0
Loader version: 3.4
Processors: 4
Processor type: Intel(R) Xeon(R) CPU L5410 @ 2.33GHz
Memory Size: 8192 MB
Memory Attributes: Bank Interleaving
Hoisting
Chipkill ECC
NVMEM Size: 1024 MB of Main Memory Used
CMOS RAM Status: OK
Service Processor Status: Unknown
IPMI: unknown
PKT: unknown
IOXM Status: present
Power: Good
Agent version: N/A
Serial Number: 5010297778
Part Number: 111-00647
Version: B0
slot 0: Dual 10G Ethernet Controller T320E-SFP/KR
Device Type: CT-FE-3
Version Number: T3-SRAM1.1.0-BR1016-02-01-FW7.7.209-DR04
Serial Number: jb04050693
c0a MAC Address: 00:a0:98:54:78:30 (auto-unknown-enabling)
c0b MAC Address: 00:a0:98:54:78:31 (auto-unknown-enabling)
slot 0: Internal BGE 10/100 Ethernet Controller
e0M MAC Address: 00:a0:98:54:78:32 (auto-unknown-down)
e0P MAC Address: 00:a0:98:54:78:33 (auto-100tx-fd-up)
Device Type: BCM5721
Sat Feb 27 18:05:03 GMT [monitor.chassisPower.degraded:notice]: Chassis power is degraded:
Sat Feb 27 18:05:03 GMT [callhome.chassis.power:error]: Call home for CHASSIS POWER DEGRADED:
slot 0: Dual 10/100/1000 Ethernet Controller G20
e0a MAC Address: 00:a0:98:54:78:2e (auto-unknown-down)
e0b MAC Address: 00:a0:98:54:78:2f (auto-unknown-down)
Device Type: Rev 6
slot 0: SAS Host Adapter 0a (PMC-Sierra PM8001 rev. C, SAS, <UP>)
Firmware rev: 01.11.06.00
Base WWN: 5:00a098:00353bf:88
Phy State: [0] Enabled, 6.0 Gb/s
[1] Enabled, 6.0 Gb/s
[2] Enabled, 6.0 Gb/s
[3] Enabled, 6.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00177+A0
QSFP Type: Passive Copper 2m ID:01
QSFP Serial Number: 123120027
ID Vendor Model FW Size
30.0 : IBM-ESXS HUC109060CSS60 J2ER 423.1GB (1172123568 512B/sect)
30.1 : IBM-ESXS HUC109060CSS60 J2ER 423.1GB (1172123568 512B/sect)
30.2 : IBM-ESXS HUC109060CSS60 J2ER 423.1GB (1172123568 512B/sect)
30.3 : IBM-ESXS HUC109060CSS60 J2ER 423.1GB (1172123568 512B/sect)
30.4 : IBM-ESXS HUC109060CSS60 J2ER 423.1GB (1172123568 512B/sect)
30.5 : IBM-ESXS HUC109060CSS60 J2ER 423.1GB (1172123568 512B/sect)
Shelf 30: IOM6 Firmware rev. IOM6 A: 0181 IOM6 B: 0181
slot 0: SAS Host Adapter 0b (PMC-Sierra PM8001 rev. C, SAS, <UP>)
Firmware rev: 01.11.06.00
Base WWN: 5:00a098:00353bf:8c
Phy State: [4] Enabled, 6.0 Gb/s
[5] Enabled, 6.0 Gb/s
[6] Enabled, 6.0 Gb/s
[7] Enabled, 6.0 Gb/s
QSFP Vendor: Molex Inc.
QSFP Part Number: 112-00177+A0
QSFP Type: Passive Copper 2m ID:00
QSFP Serial Number: 212120056
slot 0: FC Host Adapter 0c (QLogic 2432 rev. 2, L-port, <OFFLINE (hard)>)
Firmware rev: 5.4.100
Host Loop Id: 0
FC Node Name: 5:00a:098003:53bf80
FC Port Name: 5:00a:098003:53bf80
SFP Vendor: AVAGO
SFP Part Number: AFBR-57R6APZ-NA1
SFP Serial Number: B91133HJXS
SFP Capabilities: 1, 2 or 4 Gbit
Link Data Rate: N/A
slot 0: FC Host Adapter 0d (QLogic 2432 rev. 2, L-port, <OFFLINE (hard)>)
Firmware rev: 5.4.100
Host Loop Id: 0
FC Node Name: 5:00a:098103:53bf80
FC Port Name: 5:00a:098103:53bf80
SFP Vendor: AVAGO
SFP Part Number: AFBR-57R6APZ-NA1
SFP Serial Number: B91133HJXV
SFP Capabilities: 1, 2 or 4 Gbit
Link Data Rate: N/A
slot 0: Intel ICH USB EHCI Adapter u0a (0xdfe01400)
boot0 Micron Technology Real SSD eUSB 2GB, rev 2.00/11.10, addr 2 1936MB 512B/sect (0FF0022700155861)
slot 3: SAS Host Adapter 3a (PMC-Sierra PM8001 rev. C, SAS, <OFFLINE (hard)>)
MFG Part Number: USI 6086-000010-03 rev. MP V4.4
Part number: 111-00341+C0
Serial number: ST077BAD093
Date Code: 20111013
Firmware rev: 01.11.00.00
Base WWN: 5:00e004:0001a91:98
Phy State: [0] Disabled
[1] Disabled
[2] Disabled
[3] Disabled
QSFP Vendor: not available
QSFP Part Number: not available
QSFP Type: not available
QSFP Serial Number: not available
slot 3: SAS Host Adapter 3b (PMC-Sierra PM8001 rev. C, SAS, <OFFLINE (hard)>)
MFG Part Number: USI 6086-000010-03 rev. MP V4.4
Part number: 111-00341+C0
Serial number: ST077BAD093
Date Code: 20111013
Firmware rev: 01.11.00.00
Base WWN: 5:00e004:0001a91:9c
Phy State: [4] Disabled
[5] Disabled
[6] Disabled
[7] Disabled
QSFP Vendor: not available
QSFP Part Number: not available
QSFP Type: not available
QSFP Serial Number: not available
slot 3: SAS Host Adapter 3c (PMC-Sierra PM8001 rev. C, SAS, <OFFLINE (hard)>)
MFG Part Number: USI 6086-000010-03 rev. MP V4.4
Part number: 111-00341+C0
Serial number: ST077BAD093
Date Code: 20111013
Firmware rev: 01.11.00.00
Base WWN: 5:00e004:0001a91:90
Phy State: [0] Disabled
[1] Disabled
[2] Disabled
[3] Disabled
QSFP Vendor: not available
QSFP Part Number: not available
QSFP Type: not available
QSFP Serial Number: not available
slot 3: SAS Host Adapter 3d (PMC-Sierra PM8001 rev. C, SAS, <OFFLINE (hard)>)
MFG Part Number: USI 6086-000010-03 rev. MP V4.4
Part number: 111-00341+C0
Serial number: ST077BAD093
Date Code: 20111013
Firmware rev: 01.11.00.00
Base WWN: 5:00e004:0001a91:94
Phy State: [4] Disabled
[5] Disabled
[6] Disabled
[7] Disabled
QSFP Vendor: not available
QSFP Part Number: not available
QSFP Type: not available
QSFP Serial Number: not available
*> aggr status
Sat Feb 27 18:07:25 GMT [fmmb.instStat.change:info]: no mailbox instance on local side.
Sat Feb 27 18:07:25 GMT [coredump.host.spare.none:info]: No sparecore disk was found for host 0.
Sat Feb 27 18:07:25 GMT [raid.assim.tree.noRootVol:error]: No usable root volume was found!
Disk label processing failed!

unable to run aggr command
No root aggregate or root traditional volume found.
You must specify a root aggregate or traditional volume with
"aggr options <name> root" before rebooting the system.

 

Do I need Netapp oem drives ? Is there any way I can configure this storage system from scratch? vol and aggr commands

are unable to run !

 

Thanks in advance!

Hyder

1 ACCEPTED SOLUTION

akiendl
as you already mentioned. you need NetApp drives. Without that you will not be able to boot the system.

ak.

View solution in original post

2 REPLIES 2

akiendl
as you already mentioned. you need NetApp drives. Without that you will not be able to boot the system.

ak.

View solution in original post

CGandvfx

Thank you, akiendl !

I will try with Netapp oem drives 

 

 

Announcements
NetApp on Discord Image

We're on Discord, are you?

Live Chat, Watch Parties, and More!

Explore Banner

Meet Explore, NetApp’s digital sales platform

Engage digitally throughout the sales process, from product discovery to configuration, and handle all your post-purchase needs.

NetApp Insights to Action
I2A Banner
Public