nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

snapmirror matrix

leedm

Hello, I'm going to migrate from 8.2.1 cluster mode 4 node controller to new equipment, what are some ways to migrate from 8.2.1 to 9.15 os?
7 mode to cdot snapmirror is only available in 7 mode and there is no 8.2.1 information in the matrix of cdot to cdot snapmirror

Find more posts tagged with

Accepted answers

TMACMD

Not like you are thinking.
get a pair of 2720 controllers. Use those in place of the 2820. Load 9.11. Migrate data. Then head swap to 2820

All comments

SpindleNinja

There's a very long stretch... I don't think there is one controller model that exists that supports both 8.2 and 9.15.
Which model controller do you have?

TMACMD

if you are using 8.2.1, you are probably using at best some variant of the FAS80x0 series (8020/8040/8060). This platform tops out at ONTAP 9.8. I have done a few upgrades this year. Get the current cluster to ONTAP 9.8 and depending on the new equipment, you may be able to "down-rev" the new nodes to 9.10.1P(latest) and use a mixed-version cluster. vol-move everything off to the new nodes, evacuate and remove the old nodes.

There is a lot more to it than that though.

What is the starting hardware? What is the new hardware?

leedm

We plan to proceed with FAS70 or FAS2820, but it's not confirmed yet

leedm

The source equipment is FAS3250 4node and the destination equipment is probably FAS70 or FAS2820.

Sergey_Osipov

It is possible still to migrate datafrom 7-mode to up to 9.11.1

https://kb.netapp.com/on-prem/ontap/DP/SnapMirror/SnapMirror-KBs/What_are_the_restrictions_of_TDP_relationships

The relationships between 7-Mode and ONTAP clusters are supported only for transition/migration thru 9.11.1
Support for TDP was dropped in ONTAP 9.12.1 and later

TMACMD

Is the source 7-mode or cluster?

Saying a 4-node cluster indicates cluster mode as 7-mode only operates in ha pairs.

if the answer is cougar mode the accepted answer is incorrect

TMACMD

sorry about that.

if the answer is CLUSTER mode the accepted answer is incorrect

Sergey_Osipov

feels like you are right. I'm a bit confused and misinterpreted the original query as the source is 7-mode system

In this case we need to check the maximum possible ONTAP for 3250

which is 9.1 and for 2820 the lowest ONTAP is 9.13.1 (fas70 starts with 9.15.1)

We definitely do NOT support snapmirror between such a huge version difference

TMACMD

It might be worth working with NetApp.

Get a hold of a Unit that supports 9.11 (Like a FAS2720).

Build on 9.11.

Add the FAS2820 into the cluster (mixed version allowed), transition all the data over.

once the data is over, upgrade the entire cluster to 9.15. Then add in the A70 in mixed-version.

(note, I hear there are issues mixing anything higher than 9.13 with something lower, hence this method)

move any volumes off the FAS2720 and then eject the nodes from the cluster.

leedm

I'm sorry, I think I asked you the wrong question.
The source is 8.2.1 cluster mode 4 node.

leedm

I'm sorry, I think I asked you the wrong question.
The source is 8.2.1 cluster mode 4 node.

leedm

Do you mean to change from FAS32504 node to 2750 through head swap?

TMACMD

Not like you are thinking.
get a pair of 2720 controllers. Use those in place of the 2820. Load 9.11. Migrate data. Then head swap to 2820

leedm

I think we can proceed in that order.

Thank you for your advice.