hi,
I m new with NetApp
today i've got following message when i checked with sysconfig command
Vfiler-*****> sysconfig -r Aggregate aggr0 (online, raid_dp, degraded) (block checksums) Plex /aggr0/plex0 (online, normal, active, pool0) RAID group /aggr0/plex0/rg0 (degraded)
RAID Disk Device HA SHELF BAY CHAN Pool Type RPM Used (MB/blks) Phys (MB/blks) --------- ------ ------------- ---- ---- ---- ----- -------------- -------------- dparity 0c.00.0 0c 0 0 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 parity FAILED N/A 847555/1735794176 data 0c.00.2 0c 0 2 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.11 0c 0 11 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.3 0c 0 3 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.4 0c 0 4 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.7 0c 0 7 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.5 0c 0 5 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.8 0c 0 8 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.9 0c 0 9 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816 data 0c.00.6 0c 0 6 SA:B 0 SATA 7200 847555/1735794176 847884/1736466816
Pool1 spare disks (empty)
Pool0 spare disks (empty)
my parity disk is failed ! what's the reason of this message ?
what can i do ? change the hard drive ?
thanks
... View more
I know tha AFF and FAS series, can direct attach with iscsi protocol. My question is, is the same for AFF ASA?, this series include symmetric active-active and i don't know if remaining direct attach option
... View more
Hello team, For security reason I need to change all passwords on Netapp infrastructure. The controller is AFF A400 with DS 224 C. Is there any procedure existing maybe for this request? And do you know how many credential I can have to change on it? Thanks Regards,
... View more
Hi I just got a new AFF C-Series About to replicate from a FAS2750 I have 12 x 15.3TB disks. However, the aggregate I was able to create from this amounted to less than 70TB. I need this to make sense. Effective storage should get to some 100TB though, right?
... View more
Hello, everyone. I am manually obtaining autosupport logs. I configured the Ethernet port of my computer on the same network segment as the storage management port, and connected the storage e0M port with a network cable. I tried to log in to the centralized management IP/spi to obtain autosupport logs, but I found that I could not ping through the management IP address of the storage end. The computer firewall is also turned off (Because in other places my computer is able to connect to storage and access graphics pages) Is there any restriction made by the storage to deny my access?
... View more
