ONTAP Hardware

LINK NOT CONNECTED

jmishal
6,813 Views

Hello

 

I just finish  new AFF a220 setup which is attached to our Cisco MDS 9148 to and I can not get a link between the two.

I've configured both sides of FC and matched the speed. (8Gb) I must be missing something in between that I can't figure out.

This is the setting/config for one of the connections SAN side: 

Note : There is just something strange that the Physical Protocol: ethernet !!

 

CTRA::system*> fcp adapter show -instance -node CTRA-01
  (network fcp adapter show)

                          Node: CTRA-01
                       Adapter: 0c
                          UUID: 
                   Description: Fibre Channel Target Adapter 0c (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
             Physical Protocol: ethernet
                 Maximum Speed: 10
         Administrative Status: up
            Operational Status: link not connected
               Extended Status: ADAPTER UP
             Host Port Address: 0
             Firmware Revision: 8.9.0
         Data Link Rate (Gbit): 0
            Fabric Established: false
                   Fabric Name: -
        Connection Established: loop
     Is Connection Established: false
                     Mediatype: ptp
              Configured Speed: auto
      Data Protocols Supported: fcp
                   LIF Capable: true
                     THA Index: 2
                        Handle: 2
                 Physical Slot: 0
                 Original WWNN: 50:0a:09:80:0e:07:68:07
                  Adapter WWNN: 50:0a:09:80:80:43:46:b8
                  Adapter WWPN: 50:0a:09:83:80:43:46:b8
                   Queue Depth: 4096
                   Switch Port: :
    Form Factor Of Transceiver: SFP
    Vendor Name Of Transceiver: FINISAR CORP.
    Part Number Of Transceiver: FTLF8528P3BCV-QL
       Revision Of Transceiver: A
  Serial Number Of Transceiver: NT230NA
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
     Vendor OUI Of Transceiver: 00:90:65
      Wavelength In Nanometers: 850
      Date Code Of Transceiver: 15:01:12
       Validity Of Transceiver: true
                Connector Used: LC
                 Encoding Used: 8B10B
      Is Internally Calibrated: true
        Received Optical Power: 0.0 (uWatts)
    Is Received Power In Range: false
 SFP Transmitted Optical Power: 0.0 (uWatts)
        Is Xmit Power In Range: false

                          Node: CTRA-01
                       Adapter: 0d
                          UUID: 
                   Description: Fibre Channel Target Adapter 0d (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
             Physical Protocol: ethernet
                 Maximum Speed: 10
         Administrative Status: up
            Operational Status: link not connected
               Extended Status: ADAPTER UP
             Host Port Address: 0
             Firmware Revision: 8.9.0
         Data Link Rate (Gbit): 0
            Fabric Established: false
                   Fabric Name: -
        Connection Established: loop
     Is Connection Established: false
                     Mediatype: ptp
              Configured Speed: auto
      Data Protocols Supported: fcp
                   LIF Capable: true
                     THA Index: 3
                        Handle: 3
                 Physical Slot: 0
                 Original WWNN: 50:0a:09:81:0e:07:68:07
                  Adapter WWNN: 50:0a:09:80:80:43:46:b8
                  Adapter WWPN: 50:0a:09:84:80:43:46:b8
                   Queue Depth: 4096
                   Switch Port: :
    Form Factor Of Transceiver: SFP
    Vendor Name Of Transceiver: FINISAR CORP.
    Part Number Of Transceiver: FTLF8528P3BCV-QL
       Revision Of Transceiver: A
  Serial Number Of Transceiver: NT21986
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
     Vendor OUI Of Transceiver: 00:90:65
      Wavelength In Nanometers: 850
      Date Code Of Transceiver: 15:01:12
       Validity Of Transceiver: true
                Connector Used: LC
                 Encoding Used: 8B10B
      Is Internally Calibrated: true
        Received Optical Power: 0.0 (uWatts)
    Is Received Power In Range: false
 SFP Transmitted Optical Power: 0.0 (uWatts)
        Is Xmit Power In Range: false

                          Node: CTRA-01
                       Adapter: 0e
                          UUID: 
                   Description: Fibre Channel Target Adapter 0e (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
             Physical Protocol: ethernet
                 Maximum Speed: 10
         Administrative Status: up
            Operational Status: link not connected
               Extended Status: ADAPTER UP
             Host Port Address: 0
             Firmware Revision: 8.9.0
         Data Link Rate (Gbit): 0
            Fabric Established: false
                   Fabric Name: -
        Connection Established: loop
     Is Connection Established: false
                     Mediatype: ptp
              Configured Speed: auto
      Data Protocols Supported: fcp
                   LIF Capable: true
                     THA Index: 0
                        Handle: 0
                 Physical Slot: 0
                 Original WWNN: 50:0a:09:82:0e:07:68:07
                  Adapter WWNN: 50:0a:09:80:80:43:46:b8
                  Adapter WWPN: 50:0a:09:81:80:43:46:b8
                   Queue Depth: 4096
                   Switch Port: :
    Form Factor Of Transceiver: SFP
    Vendor Name Of Transceiver: FINISAR CORP.
    Part Number Of Transceiver: FTLF8528P3BCV-QL
       Revision Of Transceiver: A
  Serial Number Of Transceiver: NSR2Q2T
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
     Vendor OUI Of Transceiver: 00:90:65
      Wavelength In Nanometers: 850
      Date Code Of Transceiver: 14:12:26
       Validity Of Transceiver: true
                Connector Used: LC
                 Encoding Used: 8B10B
      Is Internally Calibrated: true
        Received Optical Power: 0.0 (uWatts)
    Is Received Power In Range: false
 SFP Transmitted Optical Power: 0.0 (uWatts)
        Is Xmit Power In Range: false

                          Node: CTRA-01
                       Adapter: 0f
                          UUID: 
                   Description: Fibre Channel Target Adapter 0f (QLogic CNA 8324 (8362), rev. 2, CNA_10G)
             Physical Protocol: ethernet
                 Maximum Speed: 10
         Administrative Status: up
            Operational Status: link not connected
               Extended Status: ADAPTER UP
             Host Port Address: 0
             Firmware Revision: 8.9.0
         Data Link Rate (Gbit): 0
            Fabric Established: false
                   Fabric Name: -
        Connection Established: loop
     Is Connection Established: false
                     Mediatype: ptp
              Configured Speed: auto
      Data Protocols Supported: fcp
                   LIF Capable: true
                     THA Index: 1
                        Handle: 1
                 Physical Slot: 0
                 Original WWNN: 50:0a:09:83:0e:07:68:07
                  Adapter WWNN: 50:0a:09:80:80:43:46:b8
                  Adapter WWPN: 50:0a:09:82:80:43:46:b8
                   Queue Depth: 4096
                   Switch Port: :
    Form Factor Of Transceiver: SFP
    Vendor Name Of Transceiver: FINISAR CORP.
    Part Number Of Transceiver: FTLF8528P3BCV-QL
       Revision Of Transceiver: A
  Serial Number Of Transceiver: NSR2G76
FC Capabilities Of Transceiver: 2,4,8 (Gbit/sec)
FC Capabilities Of Transceiver: 2, 4, 8
     Vendor OUI Of Transceiver: 00:90:65
      Wavelength In Nanometers: 850
      Date Code Of Transceiver: 14:12:26
       Validity Of Transceiver: true
                Connector Used: LC
                 Encoding Used: 8B10B
      Is Internally Calibrated: true
        Received Optical Power: 0.0 (uWatts)
    Is Received Power In Range: false
 SFP Transmitted Optical Power: 0.0 (uWatts)
        Is Xmit Power In Range: false
4 entries were displayed.

 

1 ACCEPTED SOLUTION

SpindleNinja
6,787 Views

What’s the output of “ucadmin show”. You might have to change the port from CNA to FC 

View solution in original post

3 REPLIES 3

SpindleNinja
6,788 Views

What’s the output of “ucadmin show”. You might have to change the port from CNA to FC 

jmishal
6,774 Views

This is the output of the command, and as shown by Current Mode is CNA  

 

 

CTRA::> ucadmin show
                       Current  Current    Pending  Pending    Admin
Node          Adapter  Mode     Type       Mode     Type       Status
------------  -------  -------  ---------  -------  ---------  -----------
CTRA-01       0c       cna      target     -        -          online
CTRA-01       0d       cna      target     -        -          online
CTRA-01       0e       cna      target     -        -          online
CTRA-01       0f       cna      target     -        -          online
CTRB          0c       cna      target     -        -          online
CTRB          0d       cna      target     -        -          online
CTRB          0e       cna      target     -        -          online
CTRB          0f       cna      target     -        -          online
8 entries were displayed.

 

 

Thank you for the clarification ,, I changed the mode to the fc for all adapter i need it as shown

 

 

fcp adapter modify -node CTRA-01 -adapter 0c -status-admin down

 

 

 

modify -node CTR-01 -adapter 0c -m fc

 

also i do  the same for the node B

 

seems to me everything went well.

thanks

 

SpindleNinja
6,768 Views

No problem.  Be sure to also do takeovers on each node to set the change.    And verify that each port is FC/target. 

Public