Can we still quote this model and when is it EOL? ... View more

Hi AD\Domain Admins are BUILTIN\Administrators group name members of the ONTAP vserver When the Admin account is trying to connect to the vserver within the Windows 2016 Computer Management MMC in Shared Folders / Shares section,  this error message appears : "you not not have permissions to see the list of shares for windows clients"  Thanks for your helping...   ... View more

Hi, we have to head swap from FAS8300 to FAS8700. In the documentation I can't find anything but I'm pretty sure that this is due the fact that FAS8300 and FAS8700 are basically the same storage with the processor and memory difference.    Do you have access to some documentation stating this point ?   Many thanks Luca ... View more

After update software to ontap9, and restore config to default, I have this problem. Before I can configure FAS2552 with Node Setup, configure IP and use Windows System Setup. like this example Welcome to node setup.   You can enter the following commands at any time:   "help" or "?" - if you want to have a question clarified,   "back" - if you want to change previously answered questions, and   "exit" or "quit" - if you want to quit the setup wizard.      Any changes you made before quitting will be saved.   To accept a default or omit a question, do not enter a value.       This system will send event messages and weekly reports to NetApp Technical Support. To disable this feature, enter "autosupport modify -support disable" within 24 hours. Enabling AutoSupport can significantly speed problem determination and resolution should a problem occur on your system. For further information on AutoSupport, see: http://support.netapp.com/autosupport/   Type yes to confirm and continue {yes}: yes   Enter the node management interface port [e0c]: e0M Enter the node management interface IP address: 172.16.254.100 Enter the node management interface netmask: 255.255.255.0 Enter the node management interface default gateway: 172.16.254.1 A node management interface on port e0M with IP address 172.16.254.100 has been created.     This node has its management address assigned and is ready for cluster setup.   To complete cluster setup after all nodes are ready, download and run the System Setup utility from the NetApp Support Site and use it to discover the configured nodes.   For System Setup, this node's management address is: 172.16.254.100.   Alternatively, you can use the "cluster setup" command to configure the cluster. Now I cant use this method. Node offers "Welcome to the cluster setup wizard."   Boot log:  Boot Loader version 4.3 Copyright (C) 2000-2003 Broadcom Corporation. Portions Copyright (C) 2002-2014 NetApp, Inc. All Rights Reserved. CPU Type: Intel(R) Xeon(R) CPU C3528 @ 1.73GHz Starting AUTOBOOT press Ctrl-C to abort... Loading X86_64/freebsd/image1/kernel:0x200000/10341088 0xbdcae0/5815208 Entry at 0x80293660 Loading X86_64/freebsd/image1/platform.ko:0x1169000/2266392 0x1393518/350312 0x13e8d80/269520 Starting program at 0x80293660 NetApp Data ONTAP 9.0 Trying to mount root from msdosfs:/dev/da0s1 [ro]... md0 attached to /X86_64/freebsd/image1/rootfs.img Trying to mount root from ufs:/env/md0.uzip []... mountroot: waiting for device /env/md0.uzip ... Copyright (C) 1992-2016 NetApp. All rights reserved. ******************************* * * * Press Ctrl-C for Boot Menu. * * * ******************************* Firewall rules loaded. qla_init_hw: CRBinit running ok: 8c633f NIC FW version in flash: 5.4.9 qla_init_hw: CRBinit running ok: 8c633f NIC FW version bundled: 5.4.56 Ipspace "ACP" created link speed 10Gps Module Type 10GBase-LR link speed 10Gps Module Type 10GBase-LR WAFL CPLEDGER is enabled. Checklist = 0x7ff841ff Sep 12 09:00:37 [localhost:cf.nm.nicReset:notice]: HA interconnect: Initiating soft reset on card 0 due to rendezvous reset. Sep 12 09:00:37 [localhost:cf.rv.notConnected:ALERT]: HA interconnect: Connection for 'cfo_rv' failed. add host 127.0.10.1: gateway 127.0.20.1 Sep 12 09:00:40 [localhost:cf.fm.notkoverClusterDisable:error]: Failover monitor: takeover disabled (restart) Sep 12 09:00:40 [localhost:cf.nm.nicReset:notice]: HA interconnect: Initiating soft reset on card 0 due to rendezvous reset. boot_from_disk:last_booted_OS:9.0 Sep 12 09:00:40 [localhost:kern.syslog.msg:notice]: The system was down for 168 seconds Sep 12 09:00:40 [localhost:cf.rv.notConnected:ALERT]: HA interconnect: Connection for 'cfo_rv' failed. There are 14 spare disks; you may want to use the vol or aggr command to create new volumes or aggregates or add disks to the existing aggregate. Sep 12 09:00:41 [localhost:cf.fsm.takeoverOfPartnerDisabled:error]: Failover monitor: takeover of partner disabled (Controller Failover takeover disabled). Sep 12 09:00:41 [localhost:kern.syslog.msg:notice]: domain xing mode: off, domain xing interrupt: false Sep 12 09:00:41 [localhost:clam.invalid.config:error]: Local node (name=unknown, id=0) is in an invalid configuration for providing CLAM functionality. CLAM cannot determine the identity of the HA partner. Adding /mroot/etc/swapfile as additional swap Sep 12 09:01:00 [localhost:monitor.globalStatus.critical:EMERGENCY]: Controller failover partner unknown. Controller failover not possible. Welcome to the cluster setup wizard. You can enter the following commands at any time: "help" or "?" - if you want to have a question clarified, "back" - if you want to change previously answered questions, and "exit" or "quit" - if you want to quit the cluster setup wizard. Any changes you made before quitting will be saved. You can return to cluster setup at any time by typing "cluster setup". To accept a default or omit a question, do not enter a value. Do you want to create a new cluster or join an existing cluster? {create, join}:  cf status: Takeover Node Partner Possible State Description -------------- -------------- -------- ------------------------------------- localhost - false Connected to partner. Waiting for cluster applications to come online on the local node. Offline applications: mgmt, vldb, vifmgr, bcomd, crs., Takeover is not possible: Storage failover is disabled     ... View more

Hi I  found a TR-4859 relating IBM Spectrum Scale with E-series.   I'm wondering if I can virtualize an ONTAP storage as well, my doubt is about random latency with E-series because customer would like to use the storage through Spectrum Scale to have NAS and S3 workloads.   My customer has an IBM infrasctructure and we must use such solution.   I did not find anything on IMT and IBM site about compatibility.   Many thanks Luca ... View more