There is no create cli for data protection polices, instead you should use the COPY cli. Do note, when you copy a policy the schedules are not copied along unlike when its done from the NMC( NetApp Management Console). Below is the help of copy cli. C:\>dfpm policy copy help NAME     copy -- makes copy of a policy SYNOPSIS     dfpm policy copy [ -d <description> ] <existing-policy-name-or-id>         <new-policy-name> DESCRIPTION     -d option can be used to specify description for the     new policy. C:\> ... View more

Hi      Thats a good suggestion. BTW say if your Oncommand Unified Manager has 100 Controllers do you add all the 100 it to each of your System Manager or just only a part of it ? Some might find this as a security breach. As the encryption/decryption algorithm needs to be same or shared across the products like SM and OC UM. Regards adai ... View more

Use this options to increase the job expiration timeout. dfm option set dpScheduledJobExpiration= <value> Regards adai ... View more

Hi,      When a base snapshot is lost there is no way with out a re-baseline. As the name signifies its the base, without which any resync or modify cant be done. Regards adai ... View more

You can do this by click on the edit button on the filer page. Or run the following cli. dfm host set <filerid/name/ip>   hostLogin=<username> hostpassword<userpassword> Regards adai ... View more

OnCommand Report does the consolidation of multiple DFM instance and report on its inventory and capacity. As far as I know it does not do any file level stats. Regards adai ... View more

Hi Adrian,      You will have to create using the SDK. I dont know of any other way. Regards adai ... View more

Hi Mark,      The fix in 5.0.1 will point you to OnCommand Console and not Operations Manager Console. The link will be as follows.(which is OnCommand Console) http://UPVSTNMG001.DETNSW.WIN:8080/start.html#st=1&data=(eventID=34063) Regards adai ... View more

I suggest you to try the DR policies which can be used to mirgrate data including those inside the root of the volume. The DR protection polices allows you to create your destination with same properties as primary. Which everyone would want for migration as well. Also it allow you to do a baseline, update and break and run script post and pre failover which is required for Migration too. Using this you can migrate your data between controllers. Also you can try workflow automator which gives you even more flexibility and customization. ... View more

Hi Stefan,      As I suspected, you have a lot of userquota's hundred 1000 +. But you are already on OC 5.0 64 bit  platform with a really beefy server with 64GB RAM. I suggest you to open a case with NetApp Support to look into this issue. Regards adai ... View more

Can you tell us some pattern what you observed and what tools where used to determine the same so that it helps others too. Regards adai ... View more

Hi Mark, This link with the event id should take you to a filtered list on the events page of OnCommand Console and showing only the event in question. Are you saying that this is not happening ? Can you post a screen shot on to what page it take to clicking on the link you posted ? Regards adai ... View more

Hi Stefan,      Can I have the output of dfm diag once more ? Do you have any rough estimate of what would be your userquota/qtree quota numbers ? In the mean time I strongly suggest you to open a support case so that they could do a packet trace and other troubleshooting to solve the issue as they would have all needed logs and details. Which is little difficult to share over communities for all the know reasons. Regards adai ... View more

OnCommand 5.1 the next version in development is bringing cluster mode operational,capacity and performance monitoring for Data Ontap 8.1 and 8.1.1 operating in cluster mode. As of today OnCommand 5.0/5.0.1 supports basic operational and capacity reporting for Data Ontap 8.0 and 8.1 Operating in cluster mode Regards adai ... View more

Hi Kenny,      Thats correct, but let me get more details on this and update the post. But for all reasons it can be used for restore. Its just another snapshot, which PM uses as base for snapvault. Regards adai PS:Deleted the post of crocker to improve the readability of the thread. ... View more

Any primary dir( be it a directory or a drive) is always snapvaulted to a single qtree in case of OSSV. Unlike whole volume snapvault where an entire volume with multiple qtree can be backed up to a single destination qtree. Regards adai ... View more

I got this output from mark and you are hitting the issue 595274. Pls add your case to the same. Regards adai ... View more

Hi Jon,      When you say storage migration is it primary volumes or secondary volumes( secondary aka mirror/snapvault destination). If its later, then you can use Secondary storage migration in Protection Manager to migrate the volumes which takes care of both incoming and outgoing relationship to the volume being migrated. If its  migration of primary volume using NMC/PM the volume would be unavailable to users for the entire duration of the migration and not just only during the cut-over phase. Attached is the doc that explains how to do SSM using DFM 4.0 but it holds good for any release later. ... View more

Hi Brian & Mark,           This issue is fixed in 5.0.1 expected by end of this week. You need not wait until 5.1 for this fix. Regards adai ... View more

Hi Hendrik,       Can you give us more details as to what version of DFM are you using ? BTW going forward, can you post all OnCommand related queries in the following communites instead ? OnCommand Mgmt Software Regards adai ... View more

Hi Niels,      I suspect you are using QSM, as backup policy does QSM as well and only in case of QSM each qtree requires a base snapshot on the primary to support re-sync and fail over. If you could share the snapvault status and snap list for the source and destination volume it would help. Regards adai ... View more

Hi Mark & Jeff,      Can you guys get the output of snapvault status from you sv destination filer ? Jeff,      Do you have other kind of relationship like filer to filer Qtree Snapvault or QSM or VSM ? do they show up in the appropriate transfer reports ? Regards adai ... View more

Can you click against each of the elipsis button namely resource pools, physical resource and exports on the lower right hand corner in NMC and see what events are there ? Regards adai ... View more

Can you check the same in NetApp Management Console, you are checking it in OnCommand Console. Regards adai ... View more