Active IQ Unified Manager Discussions

Do IOPS on Aggregate Performance Report include IO from cache Hits?

husselbees
18,656 Views

Hi - I'm looking to find (for each aggregate in a FAS3070 Filer) how many IOPS are being delivered at peak.

I'm working on the theory that each data disk should be capable of delivering approx 180 IOPS (they're 15k FC disks), hence I can create a "theoretical" performance limit for each aggregate, (180 x number of data disks), beyond which latency is likely to suffer.

The reason I want to know is that we are considering moving to 300GB disks, but there is little point in getting extra capacity if I can't practically make use of it (I get double the capacity but I get no more performance).

My storage admnistrator has produced an Operations Manager aggregate report (OPS Manager – ‘dfm report view aggregates-performance-summary’) showing at peak a level of IOPS that would equate to approx 600 IOPS per data disk.

600 IOPS per disk doesn't sound realistic (nobody is complaining of poor latency/performance)

Could it be that the aggregate performance report is including IOPS from Cache Hits??? (In which case this is the wrong report for me - I am purely interested in Disk IOPS).

Can anyone help?

Stu

P.S. Summary below:

Filer Name

Aggregate

# Data
Disks

Theoretical
IOPS
maximum

Monitored
IOPS

% utilised

Filer1

aggr1

70

12601

10748

85%

Filer2

aggr1

68

12241

8841

72%

Filer3

aggrebg

47

8461

10239

121%

Filer4

aggr1

37

6661

21168

318%

27 REPLIES 27

pascalduk
16,687 Views

I have been looking at this in the past. The documentation states the following for the total_transfers:

total_transfers: Total number of disk operations serviced by the aggregate per second

You would not expect caching to be in this stat, but to check this assumption I used several other commands to verify that this is the sum of  disk transfers.

Aggregate total transfers: stats show aggregate:*:total_transfers

Per disk total transfers: stats show disk:*:total_transfers

Statit (old fashioned disk utilisation report): statit -b  / statit -e

The sum of per disk transfers matched the total aggregate transfers. Also the statit output confirmed the number of disk transfers. Therefore I can safely assume that aggregate total transfers are actual disk transfers.

Then there is the question why your numbers seem too high. How where the peak numbers determined? It could be that there was a one time freak peak.

The peformance advisor has for each aggreagate a graph of total transfers over the last week. Take a look and make your own estimate of the peak disk transfers.

An other useful number is disk busy: stats show disk:*:disk_busy

If your disks are over 50% busy all the time you will normally see performance starting to degrade.

Message was edited by: pascalduk

nagesha
16,688 Views

Hi,

OpsMgr disks-performance-summary report tracks IOPS at individual disk level. We can aggregate these values for 'Filer3:aggrebg, Filer4:aggr1 ' objects and compare against

value reported  in 'aggregate-performance-summary for the same duration. Even NMC has 'Disk Summary View'  which captures IOPS at disk level, but aggregating for 37 disks is

a tedious task.

And also please let me know if you see any discrepancies between NMC Aggregate Summary View's  total_transfers counter and OpsMgr aggregate-performance-summary report

IOPS value.

regards,

nagesh

husselbees
16,687 Views

Hi - and many thanks for your response.

After initial pleasure at your explanation that cache was not included in the aggregate IOPS report, I thought i'd better do a doublecheck by comparing Aggregate stats and Disk Stats.

The commands my administrator used are:

IOPS Command - dfm report view aggregates-performance-summary

Disk Performance - dfm report view disks-performance-summary

Unfortunately there seem to be some discrepancies.

In many cases the IOPS are very very similar (but not exactly the same). For a particular aggregate however, I see 4685.13 IOPS (agg view) but a total of 2473 IOPS when adding up the constituent disk IOPS.

There was only a 0.3 second difference in the capture time - surely not enought to account for such a discrepancy?

We understand that these commands get their data from the DFM database (rather than direct from the Filer). Is tehre any reason that woudl skew the results?

Aggregate View:

Object ID Aggregate Storage System                   Total Ops/Sec

--------- --------- -------------------------------- ------------- ------------------------------ -------------------------------------

87        aggr1     filer1002       4685.13                                                                    

Per Disk View

Aggregate

Read OPS/Sec

Wrote OPS/Sec

CP Read OPS/Sec

TOTAL

aggr1

66.2

1.25

2.12

aggr1

65.53

1.08

2.17

aggr1

65.15

1.88

2.22

aggr1

64.93

1.82

2.2

aggr1

64.37

1

1.9

aggr1

64.25

0.93

2

aggr1

63.83

1.82

2.33

aggr1

63.47

1.37

2.23

aggr1

63.37

1.27

2.37

aggr1

63.23

1.23

2.22

aggr1

63.17

1.38

2.32

aggr1

63.13

1.83

2.2

aggr1

63.05

1.45

2.18

aggr1

63

1.27

2.33

aggr1

62.85

1.2

2.15

aggr1

62.72

1.32

2.35

aggr1

62.63

1.87

2.07

aggr1

62.62

1.42

2.17

aggr1

62

1.82

2.12

aggr1

61.98

1.85

2.07

aggr1

61.97

1.85

2.25

aggr1

61.93

1.87

2.32

aggr1

61.93

1.32

2.42

aggr1

61.87

1.83

1.98

aggr1

61.33

1.83

1.88

aggr1

61.1

1.28

2.22

aggr1

60.95

1.3

2.25

aggr1

60.95

1.33

2.4

aggr1

60.8

1.28

2.2

aggr1

60.8

1.28

2.07

aggr1

60.7

1.23

1.97

aggr1

60.57

1.23

2.07

aggr1

60.57

1.22

2.28

aggr1

60.5

1.18

2.2

aggr1

60.48

1.85

2.27

aggr1

59.78

1.9

2.35

aggr1

58.72

1.8

2.2

aggr1

0.38

3.12

3.6

aggr1

0.38

2.82

3.6

aggr1

0

2.17

1.68

aggr1

0

2.13

2.73

aggr1

0

2.17

1.67

aggr1

0

2.13

2.72

2307.19

69.18

97.05

2473.42

Any ideas/explanations??

BrendonHiggins
16,687 Views

Have a quick look at this powerpoint presentation as people have told me it was helpful.

Bren

http://communities.netapp.com/people/BrendonHiggins/blog/2009/10/21/sept-nug-meeting

pascalduk
16,688 Views

That is a nice one!

pascalduk
16,687 Views

husselbees wrote:

There was only a 0.3 second difference in the capture time - surely not enought to account for such a discrepancy?

I don't expect these reports to be real time and with a very variable workload this can give these differences.

You will get a better idea of your workload with the netapp cli commands I posted earlier or the performance advisor graphs.

ivan_huter
17,156 Views

Hi,

I'd like to create a report that will monitor aggregate IOPS. I'm not sure how to do this. Can you please provide some guidance?

I do have DFM but I'm unable to either create or find report that contains this information.

Thanks

nakshay
17,157 Views

Hello Ivan,

Ops manager provides for performance reports that can help you in monitoring aggregate IOPS.

From the CLI,

The report catalog that contains all aggregate related reports is :

[root@lnx218-33 ~]# dfm report catalog list | grep -i aggr

Aggregate                           Aggregates                        

[root@lnx218-33 ~]#

We can get the fields in the catalog "Aggregate":

These are the regular report fields :

[root@lnx218-33 ~]# dfm report catalog list Aggregate

Aggregate Catalog

Default Display Tab: Aggregates

Fields:

Field                               Default Name                                  Default Format

----------------------------------- --------------------------------------------- --------------

All                                 All fields of this catalog                                 

Name                                Aggregate Name                                             

FullName                            Aggregate Full Name                                        

Id                                  Aggregate Id                                               

GroupId                             Aggregate Group Id                                         

StorageSystem                       Aggregate Storage System (A)                               

Cluster                             Aggregate Cluster (A)                                      

Comment                             Aggregate Comment                                          

Type                                Aggregate Type                                             

Block Type                          Aggregate Block Type                                       

RAID                                Aggregate RAID Type                                        

State                               Aggregate State                                            

Snaplock                            SnapLock                                                   

Status                              Aggregate Status                                           

Mirrored                            Aggregate Mirrored                                         

DeletedWhen                         Aggregate Deleted When                        DD MMM 24H   

DeletedBy                           Aggregate Deleted By                                       

Used                                Aggregate Used Capacity                       KB           

UsedPct                             Aggregate Used Capacity %                    1            

FullThreshold                       Aggregate Full Threshold                      1            

NearlyFullThreshold                 Aggregate Nearly Full Threshold               1            

FullThresholdInterval               Aggregate Full Threshold Interval                          

OvercommittedThreshold              Aggregate Overcommitted Threshold             1            

NearlyOvercommittedThresh           Aggr. Nearly Overcommitted Thresh.            1            

AggrOverDeduplicatedThreshold       Aggregate Over Deduplicated Threshold         1            

AggrNearlyOverDeduplicatedThreshold Aggregate Nearly Over Deduplicated Threshold  1            

AggrSpaceSavings                    Aggregate Space Savings - Deduplication and LUN/File Clones KB           

AggrSpaceSavingsPct                 Aggregate Space Savings (%) - Deduplication and LUN/File Clones 1            

AggrDedupeVolCount                  Aggregate Volume Count - Deduplication and LUN/File Clones              

AggrPhysicalUsed                    Aggregate Physical Used                       KB           

AggrEffectiveUsed                   Aggregate Effective Used                      KB           

TotalSpace                          Aggregate Total Space                         KB           

SpaceAvailable                      Aggregate Space Available                     KB           

AvailablePct                        Aggregate Space Available in %                1            

BytesCommitted                      Aggregate Bytes Committed                     KB           

BytesCommittedPct                   Aggregate Bytes Committed %                   1            

DailyGrowthRate                     Aggregate Daily Growth Rate                   KB           

DailyGrowthPct                      Aggregate Daily Growth (%)                    1            

DaysToFull                          Aggregate Days to Full                                     

SnapshotDisabled                    Aggregate Snapshot Disabled                                

SnapshotAutoDelete                  Aggregate Snapshot Autodelete                              

SnapReserveTotal                    Aggregate Snap Reserve Total                  KB           

SnapReserveUsed                     Aggregate Snap Reserve Used                   KB           

SnapReserveUsedPct                  Aggregate Snap Reserve Used %                 1            

[root@lnx218-33 ~]#

These are the performance specific fields :

[root@lnx218-33 ~]# dfm report catalog list -P Aggregate

Aggregate Catalog

Default Display Tab: Aggregates

Fields:

Field                               Default Name                                  Default Format

----------------------------------- --------------------------------------------- --------------

TotalTransfers                      Aggregate Total Transfers Ops/Sec                          

UserReads                           Aggregate User Reads Ops/Sec                               

UserWrites                          Aggregate User Writes Ops/Sec                              

CPReads                             Aggregate CP Reads Ops/Sec                                 

PerfViolationCount                  Aggregate Perf Threshold Violation Count                   

PerfViolationPeriod                 Aggregate Perf Violation Period (Sec)                      

[root@lnx218-33 ~]#

Using report create CLI we can create a Custom report with aggregate IOPS.

[root@lnx218-33 ~]# dfm report create -R Aggregate -f FullName,StorageSystem,UserReads,UserWrites,CPReads,TotalTransfers Aggregate_IOPS

Report Aggregate_IOPS created.

Check the created report here :

[root@lnx218-33 ~]# dfm report view Aggregate_IOPS help

Aggregate_IOPS Report (Aggregate_IOPS)

Catalog Name: Aggregate

Display Tab: Aggregates

Catalog Field                                 Field Name                                    Format  

--------------------------------------------- --------------------------------------------- ---------

Aggregate.FullName                            Aggregate Full Name                                   

Aggregate.StorageSystem                       Aggregate Storage System (A)                          

Aggregate.UserReads                           Aggregate User Reads Ops/Sec                          

Aggregate.UserWrites                          Aggregate User Writes Ops/Sec                         

Aggregate.CPReads                             Aggregate CP Reads Ops/Sec                           

Aggregate.TotalTransfers                      Aggregate Total Transfers Ops/Sec                     

Default sort order is Aggregate.FullName.

[root@lnx218-33 ~]#

Hope this helps.

Thanks,

Akshay

ivan_huter
17,157 Views

Thanks Akshay for spelling this out for me. Unfortunately I was unable to create these reports and I think that's due to the fact that I have DFM 3.6. It looks like none of the Aggregate reports you referred in your post were available. I hope Operations Manager 3.8 has these Aggregate reports so I’ll go on download and install it.

What version of DFM are you running?

Thanks,

Ivan

nakshay
11,218 Views

Hello Ivan,

AFAIK, there is not much changes in the Aggregate reports from 3.6 to 3.8

Thanks,

Akshay

ivan_huter
11,219 Views

Akshay,

I have a problem that I do not have the fields you refer to. These are the field that I see when I list the Aggregate catalog.

X:\>dfm report catalog list Aggregate
Aggregate Catalog

Default Display Tab: Aggregates

Fields:

Field                          Default Name                        Default Format
------------------------------ ----------------------------------- -------------
All                            All fields of this catalog
Name                       Aggregate Name
FullName                  Aggregate Full Name
Id                             Aggregate Id
GroupId                    Aggregate Group Id
Filer                         Aggregate Filer (A)
Comment                 Aggregate Comment
Type                        Aggregate Type
RAID                        Aggregate RAID Type
State                       Aggregate State
Snaplock                 SnapLock
Status                     Aggregate Status
Mirrored                   Aggregate Mirrored
DeletedWhen           Aggregate Deleted When              DD MMM 24H
DeletedBy                Aggregate Deleted By
Used                       Aggregate Used Capacity             KB
UsedPct                  Aggregate Used Capacity %           1
FullThreshold            Aggregate Full Threshold            1
NearlyFullThreshold   Aggregate Nearly Full Threshold     1
FullThresholdInterval  Aggregate Full Threshold Interval
OvercommittedThreshold         Aggregate Overcommitted Threshold   1
NearlyOvercommittedThresh      Aggr. Nearly Overcommitted Thresh.  1
TotalSpace                     Aggregate Total Space               KB
SpaceAvailable                 Aggregate Space Available           KB
AvailablePct                   Aggregate Space Available in %      1
BytesCommitted                 Aggregate Bytes Committed           KB
BytesCommittedPct              Aggregate Bytes Committed %         1
DailyGrowthRate                Aggregate Daily Growth Rate         KB
DailyGrowthPct                 Aggregate Daily Growth (%)          1
DaysToFull                     Aggregate Days to Full
SnapshotDisabled               Aggregate Snapshot Disabled
SnapshotAutoDelete             Aggregate Snapshot Autodelete
SnapReserveTotal               Aggregate Snap Reserve Total        KB
SnapReserveUsed                Aggregate Snap Reserve Used         KB
SnapReserveUsedPct             Aggregate Snap Reserve Used %       1

So, when I run a report create command I get an error.

X:\>dfm report create -R Aggregate -f FullName,StorageSystem,UserReads,UserWrites,CPReads,TotalTransfers Aggregate_IOPS
Error: StorageSystem does not exist.
Use "dfm report catalog list" to see the list of available catalogs and fields.

Do you know what's the cause? I tried creating this report with CLI and web GUI with no luck.

Thanks for your help.

nakshay
11,219 Views

Hello Ivan,

Wish you a very happy and successful year ahead

Since you are running DFM 3.6, you will have to refer to the old name of the storage system."Filer"

>>>> Filer                         Aggregate Filer (A)

Also you obtain the performance fields using :

"dfm report catalog list -P Aggregate"

dfm report catalog list Aggregate , will only provide you with normal report fields and not performance fields.

So your final command will look like :

dfm report create -R Aggregate -f FullName,Filer,UserReads,UserWrites,CPReads,TotalTransfers Aggregate_IOPS

Note the change in the highlighted word above.

Hope that helps.

Regards,

Akshay

ivan_huter
11,217 Views

Happy New Year to you too Akshay. Thanks for taking time to help me out get to the bottom of this. Even though you say there's not much difference between 3.6 and 3.8, I came to conclusion there is. All the fields that I'm looking were introduced in version 3.7 and above. Below is the result of dfm catalog create command. As you can see dfm command and syntax you suggested does not produce desired results.

X:\>dfm report catalog list -P Aggregate
Catalog                             Default Tab
----------------------------------- -----------------------------------
Agent                               FileSRM
Appliance                           Appliances
Aggregate                           Aggregates
Disk                                Appliances
Event                               Events
Filer                               Appliances
FCPTarget                           LUNs
HBAPort                             LUNs
HostRole                            Appliances
HostUsergroup                       Appliances
HostUser                            Appliances
HostLocalUser                       Appliances
HostDomainUser                      Appliances
Interface                           Appliances
InitiatorGroup                      LUNs
IPAddress                           vFilers
LUN                                 LUNs
PrimaryDirectory                    Filesystems
Qtree                               Filesystems
SANHost                             LUNs
Script                              Scripts
ScriptJob                           Scripts
ScriptSchedule                      Scripts
SnapmirrorRelationship              Filesystems
SnapReserve                         Filesystems
Snapshot                            Filesystems
SRMPath                             FileSRM
SRMFile                             FileSRM
SRMDir                              FileSRM
User                                FileSRM
UserQuota                           FileSRM
vFiler                              vFilers
Volume                              Filesystems

However, if I type following I get aggregate fields that are available. As you can see the parameter -P is not supported in 3.6 version.

X:\>dfm report catalog list help

NAME
    list -- List the catalogs and fields available for creating a report

SYNOPSIS
    dfm report catalog list [ <catalog> ]


X:\>dfm report catalog list Aggregate
Aggregate Catalog

Default Display Tab: Aggregates

Fields:

Field                          Default Name                        Default Format
------------------------------ ----------------------------------- -------------
All                            All fields of this catalog
Name                           Aggregate Name
FullName                       Aggregate Full Name
Id                             Aggregate Id
GroupId                        Aggregate Group Id
Filer                          Aggregate Filer (A)
Comment                        Aggregate Comment
Type                           Aggregate Type
RAID                           Aggregate RAID Type
State                          Aggregate State
Snaplock                       SnapLock
Status                         Aggregate Status
Mirrored                       Aggregate Mirrored
DeletedWhen                    Aggregate Deleted When              DD MMM 24H
DeletedBy                      Aggregate Deleted By
Used                           Aggregate Used Capacity             KB
UsedPct                        Aggregate Used Capacity %           1
FullThreshold                  Aggregate Full Threshold            1
NearlyFullThreshold            Aggregate Nearly Full Threshold     1
FullThresholdInterval          Aggregate Full Threshold Interval
OvercommittedThreshold         Aggregate Overcommitted Threshold   1
NearlyOvercommittedThresh      Aggr. Nearly Overcommitted Thresh.  1
TotalSpace                     Aggregate Total Space               KB
SpaceAvailable                 Aggregate Space Available           KB
AvailablePct                   Aggregate Space Available in %      1
BytesCommitted                 Aggregate Bytes Committed           KB
BytesCommittedPct              Aggregate Bytes Committed %         1
DailyGrowthRate                Aggregate Daily Growth Rate         KB
DailyGrowthPct                 Aggregate Daily Growth (%)          1
DaysToFull                     Aggregate Days to Full
SnapshotDisabled               Aggregate Snapshot Disabled
SnapshotAutoDelete             Aggregate Snapshot Autodelete
SnapReserveTotal               Aggregate Snap Reserve Total        KB
SnapReserveUsed                Aggregate Snap Reserve Used         KB
SnapReserveUsedPct             Aggregate Snap Reserve Used %       1

I should've been more specific in my previous post. So, long story short - I'm handicapped to what I want to do with the version 3.6 and upgrade is eminent.

Thanks and regards,

Ivan

nagesha
10,748 Views

Performance Reports are introduced in DFM 3.7.

regards,

nagesh

ivan_huter
11,219 Views

Akshay,

I upgraded DFM to 3.8, created reports successfully but I'm not getting any data. Do you know what could be the problem and can you point me out in right direction. This stop-n-go is really frustrating. I'd thing this would be the one thing that should come right out of the box. It's the same thing like if you were to buy a very nice sports fast car without an od0motar, right?

Anyways, thanks for reading my rants and have a nice weekend.

Regards,

Ivan

adaikkap
9,854 Views

Hi Ivan,

     Pls check the perf status for each of the filer where you dont find any performance data.

This can be done by either running dfm host diag <filername/id> or in the NMC> Host>Setup.


Only if the perf data is collected this report will be able to show data for the performance fields.

Regards

adai

harish
9,853 Views

Hi Ivan,

Please let me know if your problem is still not resolved.

Regards

Harish

ivan_huter
9,854 Views

Adai,

thanks for your input. Here's the result of DFM command. I removed some of the proprietary info, like filer, account and domain names.

Let me know what do you think. Thanks.

X:\>dfm host diag MYFILER

Network Connectivity
IP Address             10.170.112.241
Network                10.170.112.0/22 (last searched 11 Jan 15:19)
DNS Aliases            Failed
DNS Addresses          Failed
SNMP Version in Use    SNMPv1
SNMPv1                 Passed (391 ms)
SNMP Community         XXXXXXXXX
SNMP sysName           MYFILER.com
SNMP sysObjectID       .1.3.6.1.4.1.789.2.3 (Clustered Filer)
SNMP productId         0118069635
SNMPv3                 Failed: Unknown user name
SNMPv3 Username        DOMAIN\svc_acc
ICMP Echo              Passed (0 ms)
HTTP                   Passed (0 ms)
NDMP (login not set)   Skipped
RSH                    10.170.112.241: Permission denied.
rsh: can't establish connection
SSH                    Passed (1516 ms)
RLM                    Skipped (hostRLMAddress is empty)
XML (https port 443)   Passed (78 ms)

Appliance Details
According to:   DataFabric Manager server       Host
Host Name       MYFILER.com MYFILER.com
System ID       0118069635                     0118069635
Model           FAS6080                        FAS6080
Type            Clustered Storage System       Clustered Storage System
OS Version      7.3.2                          7.3.2
Revisions       320,7.3.1,2.0.1                320,7.3.1,2.0.1

Monitoring Timestamps
Timestamp Name       Status   Interval     Default      Last Updated     Status   Error if older than ...
ccTimestamp          Normal   4 hours      4 hours                                11 Jan 11:20
cfTimestamp          Normal   5 minutes    5 minutes    11 Jan 15:18     Normal   11 Jan 15:15
cpuTimestamp         Normal   5 minutes    5 minutes    11 Jan 15:20     Normal   11 Jan 15:15
dfTimestamp          Normal   30 minutes   30 minutes   11 Jan 15:03     Normal   11 Jan 14:50
diskTimestamp        Normal   4 hours      4 hours      11 Jan 12:59     Normal   11 Jan 11:20
envTimestamp         Normal   5 minutes    5 minutes    11 Jan 15:20     Normal   11 Jan 15:15
fcTimestamp          Normal   5 minutes    5 minutes    11 Jan 15:17     Normal   11 Jan 15:15
fsTimestamp          Normal   15 minutes   15 minutes   11 Jan 15:19     Normal   11 Jan 15:05
hostPingTimestamp    Normal   1 minute     1 minute     11 Jan 15:19     Normal   11 Jan 15:19
ifTimestamp          Normal   15 minutes   15 minutes   11 Jan 15:05     Normal   11 Jan 15:05
licenseTimestamp     Normal   4 hours      4 hours      11 Jan 12:53     Normal   11 Jan 11:20
lunTimestamp         Normal   30 minutes   30 minutes   11 Jan 15:20     Normal   11 Jan 14:50
opsTimestamp         Normal   10 minutes   10 minutes   11 Jan 15:13     Normal   11 Jan 15:10
qtreeTimestamp       Normal   8 hours      8 hours                                11 Jan 07:20
rbacTimestamp        Normal   1 day        1 day        11 Jan 12:54     Normal   10 Jan 15:20
userQuotaTimestamp   Normal   1 day        1 day        11 Jan 14:01     Normal   10 Jan 15:20
sanhostTimestamp     Normal   5 minutes    5 minutes                              11 Jan 15:15
snapmirrorTimestamp  Normal   30 minutes   30 minutes                             11 Jan 14:50
snapshotTimestamp    Normal   30 minutes   30 minutes   11 Jan 14:59     Normal   11 Jan 14:50
statusTimestamp      Normal   10 minutes   10 minutes   11 Jan 15:18     Normal   11 Jan 15:10
sysInfoTimestamp     Normal   1 hour       1 hour       11 Jan 14:56     Normal   11 Jan 14:20
svTimestamp          Normal   30 minutes   30 minutes                             11 Jan 14:50
svMonTimestamp       Normal   8 hours      8 hours                                11 Jan 07:20
xmlQtreeTimestamp    Normal   8 hours      8 hours      11 Jan 14:03     Normal   11 Jan 07:20
vFilerTimestamp      Normal   1 hour       1 hour                                 11 Jan 14:20

Performance Advisor Checklist
perfAdvisorEnabled     Passed
hostType               Passed
hostRevision           Passed
hostLogin              Passed
perfAdvisorTransport   Passed

X:\>

adaikkap
9,854 Views

Hi Ivan,

     All host setting are correct, and perf status is also fine you should be able to see the aggregate performance report.

Regards

adai

harish
9,466 Views

Hi Ivan,

Please let me know if you still cannot see performance data.

Regards

Harish

Public