Is this the configuration file you want? This is from when we recently upgraded the firmware on the unit:
// Logical configuration information from Storage Array genome-cloudstore.
// Saved on February 25, 2015
// Firmware package version for Storage Array genome-cloudstore = 07.84.44.00
// NVSRAM package version for Storage Array genome-cloudstore = N26X0-784834-DB2
//on error stop;
// Uncomment the two lines below to delete the existing configuration.
//show "Deleting the existing configuration.";
//clear storageArray configuration;
// Storage Array global logical configuration script commands
show "Setting the Storage Array user label to genome-cloudstore.";
set storageArray userLabel="genome-cloudstore";
show "Setting the Storage Array media scan rate to disabled.";
set storageArray mediaScanRate=disabled;
// Uncomment the three lines below to remove the default volume (if exists). NOTE: Default volume name is always = "Unnamed".
//on error continue;
//show "Deleting the default volume created during the removal of the existing configuration.";
//delete volume["Unnamed"] removeVolumeGroup=true;
//on error stop;
// Copies the hot spare settings
// NOTE: These statements are wrapped in on-error continue and on-error stop statements to
// account for minor differences in capacity from the drive of the Storage Array on which the
// configuration was saved to that of the drives on which the configuration will be copied.
show "Setting the Storage Array cache block size to 32.";
set storageArray cacheBlockSize=32;
show "Setting the Storage Array to begin cache flush at 80% full.";
set storageArray cacheFlushStart=80;
show "Setting the Storage Array to end cache flush at 80% full.";
set storageArray cacheFlushStop=80;
// Creating Host Topology
show "Creating Disk Pool Disk_Pool_1.";
//This command creates disk pool <Disk_Pool_1>.
create diskPool drives=(99,1,1 99,2,1 99,3,1 99,4,1 99,5,1 99,1,2 99,2,2 99,3,2 99,4,2 99,5,2 99,1,3 99,2,3 99,3,3 99,4,3 99,5,3 99,1,4 99,2,4 99,3,4 99,4,4 99,5,4 99,1,5 99,2,5 99,3,5 99,4,5 99,5
,5 99,1,6 99,2,6 99,3,6 99,4,6 99,5,6 99,1,7 99,2,7 99,3,7 99,4,7 99,5,7 99,1,8 99,2,8 99,3,8 99,4,8 99,5,8 99,1,9 99,2,9 99,3,9 99,4,9 99,5,9 99,1,10 99,2,10 99,3,10 99,4,10 99,5,10 99,1,11 99,2,
11 99,3,11 99,4,11 99,5,11 99,1,12 99,2,12 99,3,12 99,4,12 99,5,12) userLabel="Disk_Pool_1" securityType=capable dataAssurance=none warningThreshold=0 criticalThreshold=0 criticalPriority=highest
degradedPriority=high backgroundPriority=low;
show "Setting the reserved drive count to 2.";
set diskPool ["Disk_Pool_1"] reservedDriveCount=2;
show "Creating volume 1 on disk pool Disk_Pool_1.";
//This command creates volume <1> on disk pool <Disk_Pool_1>.
create volume diskPool="Disk_Pool_1" userLabel="1" owner=A capacity=15294206742528 Bytes dataAssurance=none mapping=none;
show "Setting additional attributes for volume 1.";
// Configuration settings that can not be set during Volume creation.
set volume["1"] cacheFlushModifier=10;
set volume["1"] cacheWithoutBatteryEnabled=false;
set volume["1"] mirrorEnabled=true;
set volume["1"] readCacheEnabled=true;
set volume["1"] writeCacheEnabled=false;
set volume["1"] mediaScanEnabled=false;
set volume["1"] redundancyCheckEnabled=false;
set volume["1"] cacheReadPrefetch=true;
set volume["1"] modificationPriority=high;
show "Creating volume 2 on disk pool Disk_Pool_1.";
//This command creates volume <2> on disk pool <Disk_Pool_1>.
create volume diskPool="Disk_Pool_1" userLabel="2" owner=B capacity=15294206742528 Bytes dataAssurance=none mapping=none;
show "Setting additional attributes for volume 2.";
// Configuration settings that can not be set during Volume creation.
set volume["2"] cacheFlushModifier=10;
set volume["2"] cacheWithoutBatteryEnabled=false;
set volume["2"] mirrorEnabled=true;
set volume["2"] readCacheEnabled=true;
set volume["2"] writeCacheEnabled=true;
set volume["2"] mediaScanEnabled=false;
set volume["2"] redundancyCheckEnabled=false;
set volume["2"] cacheReadPrefetch=true;
set volume["2"] modificationPriority=high;
show "Creating volume 3 on disk pool Disk_Pool_1.";
//This command creates volume <3> on disk pool <Disk_Pool_1>.
create volume diskPool="Disk_Pool_1" userLabel="3" owner=A capacity=15294206742528 Bytes dataAssurance=none mapping=none;
show "Setting additional attributes for volume 3.";
// Configuration settings that can not be set during Volume creation.
set volume["3"] cacheFlushModifier=10;
set volume["3"] cacheWithoutBatteryEnabled=false;
set volume["3"] mirrorEnabled=true;
set volume["3"] readCacheEnabled=true;
set volume["3"] writeCacheEnabled=true;
set volume["3"] mediaScanEnabled=false;
set volume["3"] redundancyCheckEnabled=false;
set volume["3"] cacheReadPrefetch=true;
set volume["3"] modificationPriority=high;
show "Creating volume 4 on disk pool Disk_Pool_1.";
//This command creates volume <4> on disk pool <Disk_Pool_1>.
create volume diskPool="Disk_Pool_1" userLabel="4" owner=B capacity=15294206742528 Bytes dataAssurance=none mapping=none;
show "Setting additional attributes for volume 4.";
// Configuration settings that can not be set during Volume creation.
set volume["4"] cacheFlushModifier=10;
set volume["4"] cacheWithoutBatteryEnabled=false;
set volume["4"] mirrorEnabled=true;
set volume["4"] readCacheEnabled=true;
set volume["4"] writeCacheEnabled=true;
set volume["4"] mediaScanEnabled=false;
set volume["4"] redundancyCheckEnabled=false;
set volume["4"] cacheReadPrefetch=true;
set volume["4"] modificationPriority=high;
show "Creating volume 5 on disk pool Disk_Pool_1.";
//This command creates volume <5> on disk pool <Disk_Pool_1>.
create volume diskPool="Disk_Pool_1" userLabel="5" owner=A capacity=15294206742528 Bytes dataAssurance=none mapping=none;
show "Setting additional attributes for volume 5.";
// Configuration settings that can not be set during Volume creation.
set volume["5"] cacheFlushModifier=10;
set volume["5"] cacheWithoutBatteryEnabled=false;
set volume["5"] mirrorEnabled=true;
set volume["5"] readCacheEnabled=true;
set volume["5"] writeCacheEnabled=true;
set volume["5"] mediaScanEnabled=false;
set volume["5"] redundancyCheckEnabled=false;
set volume["5"] cacheReadPrefetch=true;
set volume["5"] modificationPriority=high;
show "Creating volume 6 on disk pool Disk_Pool_1.";
//This command creates volume <6> on disk pool <Disk_Pool_1>.
create volume diskPool="Disk_Pool_1" userLabel="6" owner=B capacity=15294378541056 Bytes dataAssurance=none mapping=none;
show "Setting additional attributes for volume 6.";
// Configuration settings that can not be set during Volume creation.
set volume["6"] cacheFlushModifier=10;
set volume["6"] cacheWithoutBatteryEnabled=false;
set volume["6"] mirrorEnabled=true;
set volume["6"] readCacheEnabled=true;
set volume["6"] writeCacheEnabled=true;
set volume["6"] mediaScanEnabled=false;
set volume["6"] redundancyCheckEnabled=false;
set volume["6"] cacheReadPrefetch=true;
set volume["6"] modificationPriority=high;
// Creating Volume-To-LUN Mappings
show "Creating Volume-to-LUN Mapping for Volume 1 to LUN 0.";
set volume ["1"] logicalUnitNumber=0 hostGroup=defaultGroup;
show "Creating Volume-to-LUN Mapping for Volume 2 to LUN 1.";
set volume ["2"] logicalUnitNumber=1 hostGroup=defaultGroup;
show "Creating Volume-to-LUN Mapping for Volume 3 to LUN 2.";
set volume ["3"] logicalUnitNumber=2 hostGroup=defaultGroup;
show "Creating Volume-to-LUN Mapping for Volume 4 to LUN 3.";
set volume ["4"] logicalUnitNumber=3 hostGroup=defaultGroup;
show "Creating Volume-to-LUN Mapping for Volume 5 to LUN 4.";
set volume ["5"] logicalUnitNumber=4 hostGroup=defaultGroup;
show "Creating Volume-to-LUN Mapping for Volume 6 to LUN 5.";
set volume ["6"] logicalUnitNumber=5 hostGroup=defaultGroup;
