Network and Storage Protocols

Inode getting filled

saranraj456
7,928 Views

Hi Friends,

We have a CIFS volume , where the inode is getting filled frequently.

It is used for scripting ( numerous no of files present in it), we normally increase the maxfile by 3 to 5 % . This seems to be temporary solution , is there any permanent fix for this?

Gone through some KB's and suggestions it is represented to recreate the volume by deleting all the data's in it . However i am looking for alternate solution rather this .

Thanks,

Saran

10 REPLIES 10

MSPJ119235
7,865 Views

Hello Saran,

Please try extending the volume if possible, It'll solve your problem.

saranraj456
7,865 Views

volume have enough space on it , apart that do we need to increase it.

Saran

HENRYPAN2
7,865 Views

Hi Saran,

You may wish to try:

Filer> vol options <Volname>

You will see one of the vol option maxdirsize=xxxxxx. I'll suggest to increase that maxdirsize for about 10% due to too high of the max dir size could hurt the filer's performance.

Then run:

Filer> vol options <Volname> maxdirsize=<current max dir size number + 10% increase>

Filer> vol options <Volname>

To verify the change.

Good luck

Henry




saranraj456
7,865 Views

Hi,

Looking for some permanent fix, not to increase the max dir size

Saran

billshaffer
7,865 Views

Your permanent fix is to stop writing new files to the volume.  Every time you write a file, you use up at least one inode.  There is a finite number of inodes available in a volume - this can be increased with the maxdirsize option, but all you're doing there is resetting that finite number. As HenryPan2 points out, there are performance implications for increasing this value (though in truth I've modified it many times and never seen an impact).

So if you truly want a permanent fix, you need to remove data from the volume.  Archive/delete some old stuff.  Migrate to a new volume.  But if you continue to write files in this volume, you will continue to use inodes, and you will continue to run into this problem.

Hope that helps

Bill

saranraj456
7,865 Views

am  seeing the number of inodes size has literally increased above the size of the volume.

Current volume size is 250 gb, but the max size is 16050000. ( it is 32 bit aggr)

Saran

aborzenkov
7,865 Views

Nitpicking - maxdirsize is irrelevant here. This is maxfiles option.

Отправлено с iPhone

20 дек. 2013 г., в 20:22, "billshaffer" <xdl-communities@communities.netapp.com<mailto:xdl-communities@communities.netapp.com>> написал(а):

<https://communities.netapp.com/index.jspa>

Re: Inode getting filled

created by billshaffer<https://communities.netapp.com/people/billshaffer> in Data ONTAP - View the full discussion<https://communities.netapp.com/message/122776#122776>

Your permanent fix is to stop writing new files to the volume. Every time you write a file, you use up at least one inode. There is a finite number of inodes available in a volume - this can be increased with the maxdirsize option, but all you're doing there is resetting that finite number. As HenryPan2 points out, there are performance implications for increasing this value (though in truth I've modified it many times and never seen an impact).

So if you truly want a permanent fix, you need to remove data from the volume. Archive/delete some old stuff. Migrate to a new volume. But if you continue to write files in this volume, you will continue to use inodes, and you will continue to run into this problem.

Hope that helps

Bill

Reply to this message by replying to this email -or- go to the message on NetApp Community<https://communities.netapp.com/message/122776#122776>

Start a new discussion in Data ONTAP by email<mailto:discussions-community-products_and_solutions-data_ontap@communities.netapp.com> or at NetApp Community<https://communities.netapp.com/choose-container.jspa?contentType=1&containerType=14&container=2877>

billshaffer
7,865 Views

aborzenkov is correct (thanks) - it is the maxfiles vol options, not the maxdirdize.

saranraj456
7,865 Views

Is there any solution to do with no or less disruption ?

Saran

MSPJ119235
7,018 Views

if you can extend the volume, it'll increase the inodes. i.e. if you double the size of volume, inodes will be doubled. You can verify it by creating a test volume.

Public