ONTAP Hardware

Identifying failed disk

vims
91,799 Views

Hi 

I have an aggregate with 4 raid groups. 

Received a messages about not enough spare disks in pool.

Looked at the filer and figure out there are 2 failed disk. However there is no amber light on a disk and there is no information in output of aggr status -r command  about failed disk location. 

Tried to compare 2 outputs show disk and storage show disk, found three missing drives. I replaced those 3 drives and the issue still there.

Thinking  of backplane failure... 

Any advices really appreciated. 

Thanks 

 

FILER2*> aggr status -r

Aggregate aggr0 (online, raid_dp) (block checksums)
Plex /aggr0/plex0 (online, normal, active, pool0)
RAID group /aggr0/plex0/rg0 (scrubbing 2% completed, block checksums)

RAID Disk Device HA SHELF BAY CHAN Pool Type RPM Used (MB/blks) Phys (MB/blks)
--------- ------ ------------- ---- ---- ---- ----- -------------- --------------

Aggregate aggr1 (online, raid_dp, degraded) (block checksums)

Plex /aggr1/plex0 (online, normal, active, pool0)
RAID group /aggr1/plex0/rg0 (scrubbing 3% completed, block checksums)

RAID Disk Device HA SHELF BAY CHAN Pool Type RPM Used (MB/blks) Phys (MB/blks)
--------- ------ ------------- ---- ---- ---- ----- -------------- --------------
dparity 0a.73 0a 4 9 FC:B 0 FCAL 10000 136000/278528000 137422/281442144
parity 0d.82 0d 5 2 FC:B 0 FCAL 10000 136000/278528000 139072/284820800
data 0d.70 0d 4 6 FC:B 0 FCAL 10000 136000/278528000 139072/284820800 

--

RAID group /aggr1/plex0/rg1 (degraded, scrubbing 3% completed, block checksums)

RAID Disk Device HA SHELF BAY CHAN Pool Type RPM Used (MB/blks) Phys (MB/blks)
--------- ------ ------------- ---- ---- ---- ----- -------------- --------------
dparity FAILED N/A 136000/ -
parity 0d.28 0d 1 12 FC:B 0 FCAL 10000 136000/278528000 137422/281442144
data 0a.69 0a 4 5 FC:B 0 FCAL 10000 136000/278528000 139072/284820800
data 0d.21 0d 1 5 FC:B 0 FCAL 10000 136000/278528000 137422/281442144
data 0a.90 0a 5 10 FC:B 0 FCAL 10000 136000/278528000 139072/284820800

 

RAID group /aggr1/plex0/rg2 (degraded, scrubbing 0% completed, block checksums)

RAID Disk Device HA SHELF BAY CHAN Pool Type RPM Used (MB/blks) Phys (MB/blks)
--------- ------ ------------- ---- ---- ---- ----- -------------- --------------
dparity 0c.112 0c 7 0 FC:B 0 FCAL 10000 136000/278528000 137104/280790184
parity 0a.32 0a 2 0 FC:B 0 FCAL 10000 136000/278528000 137422/281442144
data 0d.52 0d 3 4 FC:B 0 FCAL 10000 136000/278528000 139072/284820800
data 0a.80 0a 5 0 FC:B 0 FCAL 10000 136000/278528000 139072/284820800
data 0d.64 0d 4 0 FC:B 0 FCAL 10000 136000/278528000 139072/284820800
data 0a.112 0a 7 0 FC:B 0 FCAL 10000 136000/278528000 137104/280790184
data 0c.113 0c 7 1 FC:B 0 FCAL 10000 136000/278528000 137104/280790184
data 0a.33 0a 2 1 FC:B 0 FCAL 10000 136000/278528000 137485/281570072
data 0a.54 0a 3 6 FC:B 0 FCAL 10000 136000/278528000 139072/284820800
data 0d.81 0d 5 1 FC:B 0 FCAL 10000 136000/278528000 139072/284820800
data 0d.65 0d 4 1 FC:B 0 FCAL 10000 136000/278528000 137422/281442144
data 0d.113 0d 7 1 FC:B 0 FCAL 10000 136000/278528000 137104/280790184
data 0c.114 0c 7 2 FC:B 0 FCAL 10000 136000/278528000 137422/281442144
data 0a.37 0a 2 5 FC:B 0 FCAL 10000 136000/278528000 137485/281570072
data FAILED N/A 136000/ -
data 0d.84 0d 5 4 FC:B 0 FCAL 10000 136000/278528000 139072/284820800

 

Pool1 spare disks (empty)

Pool0 spare disks (empty)

 

15 REPLIES 15

rmatsumoto
91,724 Views

You can look at sysconfig -a and see if any disks are missing/bypassed/failed.  If you have a guess as to when they failed, or failed within a month, then you can probably look at the oldest weekly_log ASUP and compare its sysconfig -r output.   I'm not sure if you can get those disks replaced, though.  If your root vol snapshots go back far enough then you can look in there and look at their oldest messages.0/.1/.2/.3/.4/.5 file and see when the disks failed.  

vims
91,718 Views

Hi 

- sysconfig -r shows the same information. 

- log files informing about data disk failed in rg1 

autosupport files available for a month, however did not find any useful info there. Might be looking at the wrong place. Man Sad

Filer doesn't send autosupport to NetApp, looking at the local files in /etc/log directory. 

Cheers 

 

rmatsumoto
91,698 Views

I don't know which version of ONTAP it's running, but if you look in /etc/log/autosupport you will probably find a number of directories for each ASUP that's generated.  I get that it's not sending ASUPs to NetApp but if it's getting generated it'll be there.  And some of these ASUPs will have sysconfig -r output so if you look for old ones, you can probably find it.  Having said that, you may also look through sysconfig -a and look at disk IDs and maybe you can find some missing disk IDs.  For DS14 types the IDs run in 14 consecutive numbers with 2 missing numbers between shelves:

 

ID 16-29 for shelf 1

ID 32-45 for shelf 2, so on.  

 

So you know the numbers you're supposed to be missing(30, 31, 46, 47, etc)  If you're missing some IDs that should NOT be missing(43, for example), then it's probably not a bad guess that that's the missing/bypassed/failed disk.  You may also need to do this from both nodes in a cluster(if this is an HA pair).  Sometimes one node can report healthy status while the other won't.  

 

 

georgevj
91,681 Views

You could also try "storage show hub" and "fcadmin device_map" commands to view similiar information.

If this post resolved your issue, help others by selecting ACCEPT AS SOLUTION or adding a KUDO.
Cannot find the answer you need? No need to open a support case - just CHAT and we’ll handle it for you.

vims
91,667 Views

ok. found one 0d.20. Hoever in rg2 there was no luck 🙂

it failed a while ago. These findings actualy are the same as i compared two outputs i was talking above.

will try to swap disk one more time. 


RAID group /aggr1/plex0/rg1 (normal, block checksums)

      RAID Disk Device HA  SHELF BAY CHAN Pool Type  RPM  Used (MB/blks)    Phys (MB/blks)
      --------- ------ ------------- ---- ---- ---- ----- --------------    --------------
      dparity  0d.20  0d    1   4   FC:B   0  FCAL 10000 136000/278528000  137422/281442144 (prefail)
      parity   0a.28  0a    1   12  FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0d.69  0d    4   5   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data     0a.21  0a    1   5   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0d.90  0d    5   10  FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data     0d.29  0d    1   13  FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0a.22  0a    1   6   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0a.35  0a    2   3   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0c.125 0c    7   13  FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      data     0d.23  0d    1   7   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0a.75  0a    4   11  FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0d.24  0d    1   8   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0a.121 0a    7   9   FC:B   0  FCAL 15000 136000/278528000  137104/280790184
      data     0d.25  0d    1   9   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0a.26  0a    1   10  FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0a.27  0a    1   11  FC:B   0  FCAL 10000 136000/278528000  137422/281442144

    RAID group /aggr1/plex0/rg2 (degraded, block checksums)

      RAID Disk Device HA  SHELF BAY CHAN Pool Type  RPM  Used (MB/blks)    Phys (MB/blks)
      --------- ------ ------------- ---- ---- ---- ----- --------------    --------------
      dparity  0c.112 0c    7   0   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      parity   0a.32  0a    2   0   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0d.52  0d    3   4   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data     0a.80  0a    5   0   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data     0d.64  0d    4   0   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data     0a.112 0a    7   0   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      data     0c.113 0c    7   1   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      data     0a.33  0a    2   1   FC:B   0  FCAL 10000 136000/278528000  137485/281570072
      data     0d.54  0d    3   6   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data     0a.81  0a    5   1   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data     0d.65  0d    4   1   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0a.113 0a    7   1   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      data     0c.114 0c    7   2   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data     0d.37  0d    2   5   FC:B   0  FCAL 10000 136000/278528000  137485/281570072
      data FAILED  N/A                        136000/ -
      data     0a.84  0a    5   4   FC:B   0  FCAL 10000 136000/278528000  139072/284820800

vims
91,665 Views

swapped one drive,  it became a data disk in rg2.

RAID group /aggr1/plex0/rg2 (reconstruction 1% completed, block checksums)

      RAID Disk Device  HA  SHELF BAY CHAN Pool Type  RPM  Used (MB/blks)    Phys (MB/blks)
      --------- ------  ------------- ---- ---- ---- ----- --------------    --------------
      dparity   0c.112  0c    7   0   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      parity    0d.32   0d    2   0   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data      0d.52   0d    3   4   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data      0d.80   0d    5   0   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data      0d.64   0d    4   0   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data      0d.112  0d    7   0   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      data      0c.113  0c    7   1   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      data      0d.33   0d    2   1   FC:B   0  FCAL 10000 136000/278528000  137485/281570072
      data      0d.54   0d    3   6   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data      0d.81   0d    5   1   FC:B   0  FCAL 10000 136000/278528000  139072/284820800
      data      0d.65   0d    4   1   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data      0d.113  0d    7   1   FC:B   0  FCAL 10000 136000/278528000  137104/280790184
      data      0c.114  0c    7   2   FC:B   0  FCAL 10000 136000/278528000  137422/281442144
      data      0d.37   0d    2   5   FC:B   0  FCAL 10000 136000/278528000  137485/281570072
      data      0a.20   0a    1   4   FC:B   0  FCAL 10000 136000/278528000  137422/281442144 (reconstruction 1% completed)
      data      0d.84   0d    5   4   FC:B   0  FCAL 10000 136000/278528000  139072/284820800

vims
91,661 Views

The problem solved. The easy way is just compare 2 outputs as i described above.

Love the message - System Global Status is Normal Smiley Happy

thanks everyone

VIKAS_MAURYA
91,470 Views

Hello Everyone,

 

Can anybody tell me how to get failed disk report on unified manager dashboard GUI. I am able to get the failed disk list using SSH on filers but want this report on OUM dashboard.

Please let me how can get this done with my onCommand unified manager dashboard.

 

Thanks in advance.
Vik

vims
91,453 Views

@VIKAS_MAURYA wrote:

Hello Everyone,

 

Can anybody tell me how to get failed disk report on unified manager dashboard GUI. I am able to get the failed disk list using SSH on filers but want this report on OUM dashboard.

Please let me how can get this done with my onCommand unified manager dashboard.

 

Thanks in advance.
Vik


I jist tried it, rarely use it. CLI 99.9% 🙂
I think you can get it if you go to Storage tab, then pick your controller, from the drop down pick Disks.

All disks will be listed and the staus column most likely says "failed". I do not have any failed disks at the moment to confirm it, but I think it is the way to do it in OUM.

Hope it helps

VIKAS_MAURYA
41,269 Views

Many thanks KUDO..

 

I tried the same but no luck.

 

Though I have 3 failed disk in the selected controller(I can see it from CLI) but OUM does not show this value under more info tab under Storage section.

 

Kindly refer the snap shots for details.

 

Could you please let me know about the configuration which can give me the refelection of failed disk under more info tab.

 

Thanks in advance..

vims
41,242 Views

i think you are looking at the different place in OUM. Your bottom tab does not have the status column for a disk.

see attched screenshot.

VIKAS_MAURYA
41,232 Views

 Hi VIM,

 

Thanks for your valuable response.

 

I looked on the same page you suggested but it does not show the failed disk status.

 

Yesterday I was trying to upload two sceen shots for others reference but it allows only one snap shot so I uploaded only one.

 

Please refer the below snap shot.

 

Untitled3.png

 

I have three failed disks in controller named Asimov but it does not show in OUM. Also it does not have status in all status catagories.

 

Please refer the CLI snap shot.

 

Asimov1.png

 

CLI has three failed disks but it does not appear in OUM.

 

Kindly correct me if I am wrong and not able to find the correct thing on GUI.

 

Thanks in advance.

vims
41,220 Views

Hi

I just simply simulated failed drive in lab and what i figured out.

As you can see on CLI screenshot  the drive 0a.17 has the status failed,

however in OUM the same disk has status Active. More over if you try to filter disks there is no filter Failed. (last screenshot).

I think it is by design  and the way OUM report back to you.

 

 

ScreenShot008.jpg


ScreenShot007.jpg

 

ScreenShot009.jpg

VIKAS_MAURYA
41,198 Views

Thanks a ton VIM for your valuable response.

 

 

VIKAS_MAURYA
41,181 Views

Hi Everyone,

I have NetApp FAS3140 filer. It suddenly started rebooting. I tried to make it up and running but no luck. I checked on the diagnostic it seems either NVRAM is faulty or motherboard.

Could anyone suggest by referring the errors on the snap shot, what is the exact problem with the filer and what will be the resolution for it.

NVRAM Error.PNG


Many Thanks in advance.

Public