The transition to NetApp MS Azure AD B2C is complete. If you missed the pre-registration, you will be invited to reigister at next log in.Please note that access to your NetApp data may take up to 1 hour.To learn more, read the FAQ and watch the video.Need assistance? Complete this form and select “Registration Issue” as the Feedback Category.
I have two other of these shelfs that are fine and the FAS250 worked with those before I put them in production, its a spare 250 too. One shelf I'd suspect the shelf, but not both. Is there something internal to the shelfs that I might need to do? Both shelfs were used in a multi-shelf environment. And I've set them to ID 1 as well.
Is a terminator absoultely required for the FC channel to work? My two production system have no terminators and they work fine, but
I also read something about RoHS vs non-RoHS and for sure a copper based FC has to be terminated. Both extra shelves are non-RoHS.
Going into Maint 4a always gives no disks found.
*> disk show -v Warning: Software-based disk ownership is not currently being used on this system. Local System ID: XXXXXXXXX
disk show: No disks attached to system.
On boot up:
NetApp Release 7.3.2: Thu Oct 15 04:24:11 PDT 2009 Copyright (c) 1992-2009 NetApp. Starting boot on Wed Dec 31 23:59:58 GMT 1969 Thu Jan 1 00:00:27 GMT [nvram.battery.state:info]: The NVRAM battery is current ly ON. This boot is of OS version: NetApp Release 7.3.2. The last time this filer booted, it used OS version: <unknown>. The WAFL/RAID versions of the previously booted OS are unknown. If you choose a boot option other than Maintenance mode or Initialize disks, the file system of your filer might be upgraded to a new version of the OS. If you do not want to risk having your file system upgraded, choose Maintenance mode or reboot using the correct OS version.
(1) Normal boot. (2) Boot without /etc/rc. (3) Change password. (4) Initialize all disks. (4a) Same as option 4, but create a flexible root volume. (5) Maintenance mode boot.
Selection (1-5)? 4a NVLOG: UNKNOWN nvram magic value (0x1be81000)
WARNING: nvlog_test: Unexpected nvlog contents. Will discard contents of nvlog, USER DATA MAY BE LOST
PANIC: This system has no disks, and thus no file system can be created on it in process rc on release NetApp Release 7.3.2 on Thu Jan 1 00:00:56 GMT 1970
*> sysconfig -v Thu Jan 1 00:00:55 GMT [shelf.config.unknown:info]: System storage configuratio n is unknown NetApp Release 7.3.2: Thu Oct 15 04:24:11 PDT 2009 System ID: System Serial Number: System Rev: J0 System Storage Configuration: Unknown System ACP Connectivity: No Connectivity slot 0: System Board 600 MHz (TSANTSA E0) Model Name: FAS250 Part Number: 110-00016 <-- Non-RoHS Revision: E0 Serial Number: Firmware release: CFE 1.2.0 Processors: 1 Processor revision: B2 Processor type: 1250 Memory Size: 510 MB NVMEM Size: 64 MB of Main Memory Used slot 0: FC Host Adapter 0b (Dual-channel, QLogic 2312 rev. 2, 32-bit, L- port, <OFFLINE (hard)>) Firmware rev: 3.3.27 Host Loop Id: 0 FC Node Name: 5:00a:098000:0031f2 Cacheline size: 8 FC Packet size: 2048 SRAM parity: Yes External GBIC: No Link Data Rate: 1 Gbit slot 0: FC Host Adapter 0c (Dual-channel, QLogic 2312 rev. 2, 32-bit, L- port, <OFFLINE (hard)>) Firmware rev: 3.3.27 Host Loop Id: 0 FC Node Name: 5:00a:098100:0031f2 Cacheline size: 8 FC Packet size: 2048 SRAM parity: Yes External GBIC: No Link Data Rate: 1 Gbit slot 0: Dual SB1250-Gigabit Ethernet Controller Device Type: BCM1250 e0a MAC Address: 00:a0:98:01:e3:4f (auto-unknown-cfg_down) e0b MAC Address: 00:a0:98:01:e3:50 (auto-unknown-cfg_down) slot 0: ATA/IDE Adapter 0a (0x00000000000001f0) 0a.0 SanDisk SDCFB-256-911B HDX 2.15 245MB 51 2B/sect (109320B2405W2954)
If I remember correctly, the FAS250 couldn't have more than 14 disks. The FC link is there for tape backup. There should be no ESH module in the shelf, just the "head" in the "A" slot. FAS250 systems always came with a "blind" module that just filled slot B.
In any case, it seems like your disks need to be assigned to the filer, but I can't remember for sure. The FAS270 always used disk ownership.
After you remove the ESH module from slot B, try booting into maintenance mode ("5") and see if you can see the disks there.
Progress! After swapping things around, putting in an esh card vs. esh2 card, etc.... Still not luck. However, I think decided to remove all the drives and see what happens.
0b stayed up!
Popping a drive in slot 0 and we get:
Thu Jan 1 00:08:06 GMT [fci.link.break:error]: Link break detected on Fibre Channel adapter 0b. Thu Jan 1 00:05:51 GMT [fci.link.error:error]: Could not recover link on Fibre Channel adapter 0b after 30 seconds. Offlining the adapter. Thu Jan 1 00:05:51 GMT [fci.adapter.offline:info]: Fibre Channel adapter 0b is now offline.
Note: This ONLY happens when a drive (any drive) is put into slot 0! I was able to populate the chassis from 1-13 and now show 13 drives online and 4a is building me a file system!
But why???? What is unique or configured in this ds14/mk2 chassis (both of them) that slot 0 brings down 0b? I suspect something with clustering maybe? Is there some switch or config I need to do to the chassis to fix this? At least I've confirmed it's not my spare head....
DISK CHAN VENDOR PRODUCT ID REV SERIAL# HW (BLOCKS BPS) DQ