ONTAP Discussions

Can't assign IP Address to the SVM

stas148
4,093 Views

Hi,

 

I've got an interesting trouble with FAS2650 SVM configuration, I can't assign IP Address to the SVM through OnCommand Manager:

 

Untitled.jpg

 

but it's working perfect through CLI.

Any ideas?

1 ACCEPTED SOLUTION

AlexDawson
3,961 Views

Hi there,

 

I would say it is "common knowledge" - it is described as a “management” port, this topic is also covered in all of our training courses, and at a minimum here, page 32 - https://www.netapp.com/us/media/tr-4182.pdf

On some of our platforms this port has only been 100Mbit in the past, and due to the physical port also hosting the service processor, it cannot support VLAN tags, or mtu other than 1500

 

Edit: Is it possible this system has SFP to RJ45 adapters in slots e0a and e0b? I see admin speed is set to 1GB instead of 10GB. Normally you would use twinax cables to plug e0a to e0a and e0b to e0b, and then use the SFP to RJ45 ethernet adapters in e0c and e0d to plug in regular ethernet (it looks like e0e and e0f are set to FC personality)

View solution in original post

6 REPLIES 6

AlexDawson
4,046 Views

Hi there,

 

Can you please post the output of these commands:

 

network port show
network port broadcast-domain show
network subnet show

stas148
4,022 Views

Here you go:

 

fas2650::> network port show

Node: fas2650-n1
                                                  Speed(Mbps) Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status
--------- ------------ ---------------- ---- ---- ----------- --------
e0M       Default      Management       up   1500  auto/1000  healthy
e0a       Cluster      Cluster          up   9000  1000/10000 healthy
e0b       Cluster      Cluster          up   9000  1000/10000 healthy
e0e       Default      -                down 1500  auto/-     -
e0f       Default      -                down 1500  auto/-     -

Node: fas2650-n2
                                                  Speed(Mbps) Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status
--------- ------------ ---------------- ---- ---- ----------- --------
e0M       Default      Management       up   1500  auto/1000  healthy
e0a       Cluster      Cluster          up   9000  1000/10000 healthy
e0b       Cluster      Cluster          up   9000  1000/10000 healthy
e0e       Default      -                down 1500  auto/-     -
e0f       Default      -                down 1500  auto/-     -
10 entries were displayed.

fas2650::> network port broadcast-domain show
IPspace Broadcast                                         Update
Name    Domain Name    MTU  Port List                     Status Details
------- ----------- ------  ----------------------------- --------------
Cluster Cluster       9000
                            fas2650-n2:e0a           complete
                            fas2650-n2:e0b           complete
                            fas2650-n1:e0a           complete
                            fas2650-n1:e0b           complete
Default Management    1500
                            fas2650-n2:e0M           complete
                            fas2650-n1:e0M           complete
2 entries were displayed.

fas2650::> network subnet show

IPspace: Default
Subnet                     Broadcast                   Avail/
Name      Subnet           Domain    Gateway           Total   Ranges
--------- ---------------- --------- --------------- --------- ---------------
mgm       10.112.0.0/16    Management
                                     10.112.0.1         1/4    10.112.5.202-10.112.5.204,
                                                               10.112.5.207

AlexDawson
4,007 Views
Hi there - you can’t host data LIFs on e0M and the only other ports up are Cluster ports. Please connect more ports and try again.

stas148
3,988 Views

Hi there,

Is it common knowlege? I don't see anything about it at the docs.netapp.com 

AlexDawson
3,962 Views

Hi there,

 

I would say it is "common knowledge" - it is described as a “management” port, this topic is also covered in all of our training courses, and at a minimum here, page 32 - https://www.netapp.com/us/media/tr-4182.pdf

On some of our platforms this port has only been 100Mbit in the past, and due to the physical port also hosting the service processor, it cannot support VLAN tags, or mtu other than 1500

 

Edit: Is it possible this system has SFP to RJ45 adapters in slots e0a and e0b? I see admin speed is set to 1GB instead of 10GB. Normally you would use twinax cables to plug e0a to e0a and e0b to e0b, and then use the SFP to RJ45 ethernet adapters in e0c and e0d to plug in regular ethernet (it looks like e0e and e0f are set to FC personality)

stas148
3,889 Views

Hi,

 

"Is it possible this system has SFP to RJ45 adapters in slots e0a and e0b?" - no, there was a misconfiguration, I've changed admin speed:

 

Node: fas2650-n1
                                                  Speed(Mbps) Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status
--------- ------------ ---------------- ---- ---- ----------- --------
e0M       Default      Management       up   1500  auto/1000  healthy
e0a       Cluster      Cluster          up   9000 10000/10000 healthy
e0b       Cluster      Cluster          up   9000 10000/10000 healthy
e0e       Default      -                down 1500  auto/-     -
e0f       Default      -                down 1500  auto/-     -

Node: fas2650-n2
                                                  Speed(Mbps) Health
Port      IPspace      Broadcast Domain Link MTU  Admin/Oper  Status
--------- ------------ ---------------- ---- ---- ----------- --------
e0M       Default      Management       up   1500  auto/1000  healthy
e0a       Cluster      Cluster          up   9000 10000/10000 healthy
e0b       Cluster      Cluster          up   9000 10000/10000 healthy
e0e       Default      -                down 1500  auto/-     -
e0f       Default      -                down 1500  auto/-     -

 

"connect more ports and try again" - thanks for the advice, i'm gonna test it out

Public