Hi all,
This is a FAS2240-2 2-node Data Ontap 9.0
Just upgraded from Ontap 8.3RC2
The volumes under vserver are having cifs/nfs exports.
cifs/nfs volumes can be mounted, data read/write works properly on them.
When I added the Ontap 9.0 into a ndmp backup software , browsing works to see all the volumes under the vserver.
But when I was performing a backup.
The netapp Data Ontap 9.0 reported error ,
Here is the log from Netapp side:
MGMT_RPC::rpc_msg_input: 0x81041b400 here buf 0x0x81048e000 length 140
00000006.0000c7ee 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: MGMT_RPC::msg: incoming SERVER message 0x81041b400
00000006.0000c7ef 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: MGMT_RPC::using procedure 6 (procnum 10)
00000006.0000c7f0 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: MGMT_RPC::buffer_size_check: 0x0 0 vs 100
00000006.0000c7f1 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: MGMT_RPC::buffer_size_check: growing 0x81041b4b0 from 0 to 1024
00000006.0000c7f2 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: S<BKUP (ndmp_server) BR2NDMPD_DEBUG_LOG
00000006.0000c7f3 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: sess_handle 0xd00000000 seq 0 (0x0)
00000006.0000c7f4 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: LOG sev (3) msg (NDMP Vserver Listen: couldn't find any appropriate IP address to listen on)
00000006.0000c7f5 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: MGMT_RPC::server_reply: 0x81041b400 start
….
DATA_ABORT pending callback
00000006.0000c844 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: DATA cb_abort_on_listen_connect_failure: errnum 0: Success or No Error
00000006.0000c845 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: DATA set_ndmp_state: data_op 1 (DATA_OP_IDLE) => 1 (DATA_OP_IDLE)
00000006.0000c846 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: cb_ndmp4_data_listen: here
00000006.0000c847 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: generic_xmit_ndmp_message: start
00000006.0000c848 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: DMA<<S V4 sequence=11 (0xb)
00000006.0000c849 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: Time_stamp=0x57f8b7d5 (Oct 8 09:09:41 2016)
00000006.0000c84a 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: message type=1 (NDMP4_MESSAGE_REPLY)
00000006.0000c84b 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: message_code=0x409 (NDMP4_DATA_LISTEN)
00000006.0000c84c 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: reply_sequence=9 (0x9)
00000006.0000c84d 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: error_code=0 (NDMP4_NO_ERR)
00000006.0000c84e 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: error=7 (NDMP4_IO_ERR)
00000006.0000c84f 0093d17a Sat Oct 08 2016 09:09:41 +00:00 [kern_ndmpd:info:4052] [39093] DEBUG: addr_type=0 (NDMP4_ADDR_LOCAL)
I checked all the network interface in CLI:
Logical Status Network Current Current Is
Vserver Interface Admin/Oper Address/Mask Node Port Home
----------- ---------- ---------- ------------------ ------------- ------- ----
Cluster
clidev-fas2246-cx-01_clus1
up/up 169.254.141.39/16 clidev-fas2246-cx-01
e1a true
clidev-fas2246-cx-01_clus2
up/up 169.254.195.115/16 clidev-fas2246-cx-01
e1b true
clidev-fas2246-cx-02_clus1
up/up 169.254.247.155/16 clidev-fas2246-cx-02
e1a true
clidev-fas2246-cx-02_clus2
up/up 169.254.36.24/16 clidev-fas2246-cx-02
e1b true
clidev-fas2246-cliqa-vserver1
clidev-fas2246-cliqa-vserver1-lif1
up/up 10.6.254.201/24 clidev-fas2246-cx-01
e0a true
Does anyone know what's the possible reason for this failure?
Thanks.
