ONTAP Discussions

Move disk to another storage.

edununes
9,929 Views

Hello everyone,
Could someone explain to me what the procedure to remove the disks from one storage to be able to install in another, I need to empty an entire Shelf of disk but I need to do in parts removing half of the disks at a time, I've checked and they are not shared and I've already emptied one of the aggregates.

11 REPLIES 11

SpindleNinja
9,921 Views

just to confirm, you are moving them from one HA system over to another? 

edununes
9,781 Views

Yes from one H.A system to another.

edununes
9,774 Views

Yes from one H.A system to another.

TMACMD
9,914 Views

You would have to delete the aggregate. Get the drives to be spares.

Once they are are spares, probably turn off autoassign (disk option modify -node * -autoassign off) then remove ownership of the drives. once the owner is gone, you should be able to remove the drive and put it in another system without much of any issue.

edununes
9,780 Views

Thank you for answering, sorry for my delay because I was off duty here at the company, I opened a case at Netapp for this task and according to them I could not remove the first 12 Shelf disks as it would violate the disk population rule, I informed them that these disks are not shared and the aggregate that it has I can exclude normally, I'm waiting for his return.

edununes
9,775 Views

Thank you for answering, sorry for my delay because I was off duty here at the company, I opened a case at Netapp for this task and according to them I could not remove the first 12 Shelf disks as it would violate the disk population rule, I informed them that these disks are not shared and the aggregate that it has I can exclude normally, I'm waiting for his return.

edununes
9,758 Views

Guys,

Below is the answer given to me by Netapp.

 

 

"If you are removing disks 0-11 from disk shelf 02 the system will be moved to Single/Mixed path and redundancy to the storage will be lost.

Hence, as per the disk population rule it is not recommended to remove the disks 0-11."

Sig
9,639 Views

Hmm that surprises me.  I would not have hesitated to do just what is listed above.  I'm not sure I agree with support. When buying 1/2 populated shelves NetApp has in the recent past shipped with bays 0-11 populated (12-23 empty). Everything was HA and proper.

That said the last few I have seen have been populated 0-5 and 18-23 so perhaps something has changed but pretty sure they were the same shelf types.

 

Couple options

- Do it anyways as it's a temp state until you move the rest.

- Delete the aggr on disks 0-11 so they are spares, assign to node2.  "disk replace ...." odd disk numbers with the even spares until all odd disks are spares and all even disks are aggr disks.  remove odd disks as above.

Sig
9,638 Views

or I guess "disk replace...."

disk 12 with disk 0

disk 13 with disk 1

disk 14 with disk 2

disk 15 with disk 3

disk 16 with disk 4

disk 17 with disk 5

then move disk 6-17 (as the are now spares) to your new system

ttran
9,882 Views

Hi @edununes,

 

Spot on answer as always!!! @TMACMD.

 

It would essentially be the same steps in the following document up until step 12 as you are not preserving/migrating the aggregate, but the remaining steps to gracefully "remove" the aggregate and disks apply.

 

Physically moving an aggregate composed of disks 

 

 

Regards,

 

Team NetApp

Team NetApp

liuh
39 Views

hi

You need to use the command to remove the disk from storage, change the status of the disk you want to remove to Not Owned,

Run the disk show -v command to check whether the disk is Not Owned. Run the disk unfail -s 0a.XX.XX command to convert the disk to a hot spare disk and remove the disk manually

Public