ONTAP Discussions

re: FAS2040

nasjames
9,668 Views

Hi there I am starting from scratch to install a FAS2040 is there a setup guide any where I am not finding one

also any help would be appreciated.

1 ACCEPTED SOLUTION
31 REPLIES 31

nasjames
7,757 Views

Thanks I'll check it out

nasjames
8,092 Views

so I set the IP and subnet etc but the device is still showing something else

is there a way to force the new config

SpindleNinja
8,085 Views

You could boot into maintenance mode (ctrl-c) during boot.  and do opt 4 on each controller    that will wipe everything, including any data. 

nasjames
8,078 Views

Got it going, looking to do link aggregation ports so 2 ports work together 

 

in this case both e0a I’d like to get together 

SpindleNinja
8,070 Views

What you're looking for is called an ifgrps.   They actually can't cross controllers.   So you could bundle e0a and e0b on the same controller together.     During a failover the IPs that use that ifgrp would move to the partner and data would continue to be served out. 

nasjames
8,027 Views

hey how do you save the running config is there a wr or some command for that

for nvram with netapp

nasjames
8,025 Views

found this http://www.datadisk.co.uk/html_docs/netapp/netapp_cs.htm

but not sure if the commands are current

SpindleNinja
8,018 Views

are you thinking like a cisco device were you have to run something like "copy run start" to make sure it boots OK the next time?    - There's no need for this type of action on netapp.  

 

...or taking a backup copy just incase the root volume / aggr get corrupted?   for 7mode system, this would be a good place to start:  https://kb.netapp.com/app/answers/answer_view/a_id/1036245/~/how-to-backup-system-configuration-files-on-the-filer-   

 

nasjames
7,794 Views

Yea that’s what I was thinking , because the config when I rebooted went away 

SpindleNinja
7,791 Views

sorry about that,   give this a look over.  (been a while since I had to build a new 7mode system!)  yeah, you need to copy the same command into the etc/rc file   

 

https://library.netapp.com/ecmdocs/ECMP1368831/html/GUID-3C690A8F-691A-45F2-BA1D-05F945E14515.html  

 

 

nasjames
7,778 Views

does this allow for raid 6 instead of 4 ?

 

I cant seem to get it any higher it says raid 4 or DP

 

btw thanks for all the help

SpindleNinja
7,376 Views

DP is technically raid 6 dual parity .   https://www.netapp.com/us/products/platform-os/raid-dp.aspx   

 

 

nasjames
6,522 Views

is it possible to set an IP for the e0P management port? if so how do we do that

I tried from maintenance mode

 

no dice said I have to do it from the CLI

SpindleNinja
6,520 Views

e0P is not for data use.  I believe it's for the ACP cabling for external shelves.   

nasjames
6,518 Views

I know its not data but what if the IP is in conflict with others... I wondered how to be able to change it

SpindleNinja
6,546 Views

I have not ever heard of a conflict,  but then again people usually don't run 192.168.0.x in a corp.    

 

I found an old doc that says that you can use "acpadmin configure"  to configure the IP network.  give it a try.  

 

nasjames
6,545 Views

well there is other servers but its vm the 192....

SpindleNinja
6,537 Views

That network is only between the shelves and the controller.    

nasjames
6,529 Views

got the rc file going

 

 

Public