Talk with other users about your NetApp data storage solutions and VMware server and desktop virtualization solutions, as well as NetApp Virtual Storage Console (VSC) for VMware’s vSphere cloud computing foundation.
Talk with other users about your NetApp data storage solutions and VMware server and desktop virtualization solutions, as well as NetApp Virtual Storage Console (VSC) for VMware’s vSphere cloud computing foundation.
Hi, I have just installed Ontap Tools 10.3 and am having a problem with deploying nodes in HA setup. From my lib I managed to deploy the ontapp tools VM with the first node. But since the new ontapp tools interface, I cannot deploy the other two nodes, I have this error message: My ontaptools vm, the three nodes and the vcenter are all on the same /24. do you have any idea where this could come from? Thanks
... View more
Hi there, I have following the manual to install the ONTAP Tools for vSphere 10.3, succefully deployed the first node. After that I tried to deploy optional services, VASA provider, SRA, etc. Checked HA, filled vCenter and Content Library path same as I deployed first node, entered HA settings and allowed pre-check passed, after that deployment started but it keeps failed at 35%, and I saw it was unable to deploy node 2 and node 3 with folllowing errors: "Deleting node since deploy vms/install rke2 failed" Searched KB but no found any clues, any ideas? before I try to place a call, many thanks!
... View more
Hi there, I set the host name to NA-OTV-01, but not able to initalize the config via OVA deploy.. The Internet standards (Requests for Comments) for protocols mandate that component hostname labels may contain only the ASCII letters 'a' through 'z' (in a case-insensitive manner), the digits '0' through '9', and the hyphen ('-'). The original specification of hostnames in RFC 952, mandated that labels could not start with a digit or with a hyphen, and must not end with a hyphen. However, a subsequent specification (RFC 1123) permitted hostname labels to start with digits. No other symbols, punctuation characters, or white space are permitted. Though hyphen in the hostname is allowed, two consecutive hyphens ('--") in the hostname are not allowed.
... View more
Hi all, I don't know if this is the right board, but I will select this one. I acquired a refurbished Netapp Switch for my homelab, and I am trying to configure this, but I am getting stuck when I want to configure a port without any VLANs, and I don't know why. This Switch is connected to two HPE DL362-G9(vSphere) and a Synology. (SwitchNetApp) #show version Switch: 1 System Description............................. NetApp CN1610, 1.3.0.2, Linux 3.8.13-2de1cc1c Machine Type................................... NetApp CN1610 Machine Model.................................. CN1610 Serial Number.................................. 41011200095 Part Number.................................... 111-00982 Burned In MAC Address.......................... 00:A0:98:EA:6D:82 Software Version............................... 1.3.0.2 Operating System............................... Linux 3.8.13-2de1cc1c Network Processing Device...................... BCM56820_B0 CPLD version................................... 0x6 Additional Packages............................ FASTPATH QOS FASTPATH IPv6 Management This is my problem: I have ports from 1-5 using VLAN 10 for the storage network, and working without issues. In Synology and ESXi Storage is working all is ok with 10Gb connections. This is an example of the port configuration: (SwitchNetApp) #show running-config interface 0/1 !Current Configuration: ! interface 0/1 mtu 9216 switchport mode trunk switchport trunk allowed vlan 10 lldp transmit lldp receive lldp med exit But for the ports, I don't need VLANs, like for VMs network and ESXi management, I can't get the port to work. On the vSphere switch, everything is ok since I have another switch(1Gb) where I connect, and the ESXi and VMs have a network. But any port on NEtapp switch I try to connect I cant make it work. Ports, cables, and interface cards are ok because if I change the configuration to use VLAN10(like above), it works. Example of a port withou any VLAN: (SwitchNetApp) #show running-config interface 0/14 !Current Configuration: ! interface 0/14 switchport mode access lldp transmit lldp receive lldp notification lldp med exit I have tried everything, with native VLAN1 without, with mode access, and without, and I don't know why nothing works. Since Virtual Switch doesn't have VLAN or trunk, it should be easy, but no. What am I doing wrong here? Thank You LP
... View more
is this a supported configuration for snapcenter plugin for vmware vsphere 8.x? Datacenter 1 - location 1 - Snapcenter appliance installed and virtual center server - several VMs - VMs are on NFS stores provided by the Netapp. => backup of vms are working through snapshots Datacenter 2 - location 2 - same virtual center server who manage the ESXi Hosts but no additional Snapcenter appliance deployed. - several VMs also on NFS store provided from a different Netapp => goal: Backup VMs with snapshots from SCV in datacenter1 Currently the backup runs also on Vms on datacenter2 but it creates the snapshot on the NFS store from Datacenter1? Therefore restore will not work. thx Patrick
... View more
