Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Mute
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
What could be the reason that we are missing performance data from many many controllers for the last weeks, I have a lot of customers where both CMPG and myasup have no data for performance for the last weeks. Couple of months back it was just a few but now it is many customers for whom I cannot get any information. It seems the NetApp DB is not receiving them.
9 REPLIES 9
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
We have the same problem here. On most filers we dont see any myasup data. Asup e-mails are sent and working (for replacements i.e.).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
If possible, examine EMS event logs and messages files for any problems with the storage controller's collection and transmission of the Performance Data AutoSupport message. If there are problems, open a technical case with NetApp Support and be ready to provide the info from the logs, as well as the notifyd.log file (for 8.0 systems) in the /etc/log/mlog (7-Mode) or /mroot/etc/log/mlog (Cluster-Mode) directory.
If there's nothing amiss at the storage controller end, then file a support site ticket about My AutoSupport missing performance data for your specific systems at http://now.netapp.com/willows/pri/feedback.do
-Andris
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
recently i have to face same problem with my customer.
reason:the .GZ file will more than 10MB then it will not sent the file to autosupport.thats why we couldn't get the last week performance data in autosupport.
solution: in this cases we have to do sent the .GZ file manuvally to the autosupport.by using the command
"options autosupport.performance_data.doit daily"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Yes. See KB 2016549 for more information.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
I launched the command "options autosupport.performance_data.doit" in the controllers a week ago, but still dont see the data on MYASUP.
PS: The autosupport emails, works well.
Any idea of a solution for this?
Very thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello folks, i too have this problem.
I launched the command "options autosupport.performance_data.doit" in the controllers a week ago, but still dont see the data on MYASUP.
PS: The autosupport emails, works well.
Anyone have any solution for this?
Very thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hi Fabricio,
Can I request you log an incident using the links provided at the bottom of this page?
http://support.netapp.com/myautosupport/feedback.html
When you log the incident, please mention the system details so that our Support Team can investigate and respond.
Thanks,
Sudip
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Assuming you're running 8.1+ Data ONTAP, you can check to see if the ASUP was successfully with the "autosupport history show -instance" command. This will at least tell you if the first leg of the transmission worked. If it did, you should proceed with the My AutoSupport ticket. If it didn't, then you can open a technical case with NetApp Support to help you diagnose the transmission failure.
For more info, read this AutoSupport troubleshooting workflow KB: https://kb.netapp.com/support/index?page=content&id=2017276
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
Hello Sudip,
When i enter in this link:
http://support.netapp.com/myautosupport/feedback.html
Provided by the page you mentioned above, he enter in a loop state.
