FlexPod Discussions

Cisco UCS Direct Attached Storage for NFS

ORONA_MIKEL
27,052 Views

Hi

 

We are configurating one Flexpod solution.
UCS 6296UP with Fas8020 Ontap 8.3  Direct Attached Storage for NFS

 

This is the information found

http://www.cisco.com/c/en/us/products/collateral/servers-unified-computing/ucs-6100-series-fabric-interconnects/whitepaper_c11-702584.html

 

We are create the "appliance ports" but this are in error.

 Error: ENM source pinning failed

 

Thanks

 

1 ACCEPTED SOLUTION

ORONA_MIKEL
18,427 Views

Yes this is the solution. The system need link.

View solution in original post

13 REPLIES 13

DREW_RUSSELL
26,979 Views

It's going to be hard to troubleshoot with out many details on the configuration. To start with, make sure that the VLAN you have configured on the Appliance port exsits in both the LAN Cloud and Appliance sections.

 

 

radek_kubka
26,934 Views

Hi,

 

This blog post describes nicely solving the issue, which quite likely is due to VLAN discrepancies:

http://wahlnetwork.com/2014/09/23/enm-source-pinning-failed/

 

Regards,

Radek

ORONA_MIKEL
26,923 Views


Thanks

I am test with this configuration but the ports are in fail.
is it necesary some special parameters in NetApp (Ontap:8.3)?

I detec what when I configure with "Set Ethernet Swiching Mode" the port are up but in normal mode "End-Host Mode"they are in fail.

DREW_RUSSELL
26,921 Views

There shouldn't be any special configuration you'll need on the NetApp side. 

 

Did you test the VLAN issue mentioned?

ORONA_MIKEL
26,922 Views

Hi

Yes I configure same VLAN in two level and It's not sufficient.

Only changing mode, system reboot but I think this is not good solution.

 

Thanks

ORONA_MIKEL
26,889 Views

Hi

 

Pantallazo

 

This is how it is configured.

UCSM is in 2.1(3e) version and NetApp in 8.3

 

Thanks

 

 

 

 

Achim
26,857 Views

Hello.

 

Same issue here. Configured the vlans in both (lan cloud and appliances).

Port is in failed mode:

 

Overall Status:
 
Failed
Additional Info:ENM source pinning failed
Admin State:Enabled

ORONA_MIKEL
26,764 Views

Hi

 

My error was I not had any server created. When I create a server with vNic in this Vlan the port are turn up in "storage port" mode.

 

Other question, If Netapp port are in ifgroup in Fabric Interconet with port channel?

Thanks

SLASH5K200
18,414 Views

Hi, 

 

Im having the same problem.

 

Can i confirm that you resolved this by deploying a service profile on a blade that made use of the storage appliance vlan via a vNic Template and that fixed the error ?

 

Cheers,

 

Chris

 

 

ORONA_MIKEL
18,428 Views

Yes this is the solution. The system need link.

KSALINVILLE
18,210 Views

I know that this is a mildly dated thread, however, I've just ran into this issue at a client site where we were making a number of modifications to SnapMirror configurations with a direct-attached to UCS setup and the fix was not to add the new NetApp VLAN to a Service Profile vNIC.  The fix was to navigate to each of the appliance ports (in our case just one per fabric) and verify that the newly-created Appliance VLAN was actually checkmarked to enable it on the Applianct Ports.  It did also have to be in both the Appliance Cloud and the LAN Cloud as a Global VLAN.

 

Thanks!
Kris

 

 

Kishor
13,204 Views

Thanks Chris. In my case the issue was that I didn't create the same VLAN in the LAN cloud but only created in appliance cloud. Hence it failed. Issue got resolved after creating the same VLAN in LAN cloud after referring your solution. 

ORONA_MIKEL
26,813 Views

Hi

We view the NetApp interfaces are CNA so we are testing with Fcoe  Sotorage port. Is it right this option?

 

How confirure the vlans?

 

Thanks

 

 

 

Public