VMware Solutions Discussions

mbralign 5.2.1 will not align the correct file

support_4
views-count 5847 Views

I am trying to get mbralign to align one of my WinXP vmdk-files. I can use mbralign --scan "path" and get the message that this vmdk is not aligned.

With the machine still be shut down, I remove the --scan from the command, and then it starts trying other vmdk's on the host's VMFS volumes instead of the one I am pointing it to...?

Host is ESX4.1u1

Host Utilities are version 5.2.1

20 REPLIES 20

Re: mbralign 5.2.1 will not align the correct file

afgitdepartment
views-count 5848 Views

i'm having the same problems. i will post if i find any resolution

do your vmdk files by chance have a hypen in their name?

Re: mbralign 5.2.1 will not align the correct file

afgitdepartment
views-count 5848 Views

i believe i found a solution.  the mbrscan and mbralign in the  ESX 5.1 Host Utilities worked.

i first copied the host utility netapp_esx_host_utilities_5_1.tar.gz file to the esx host, then extracted this file with "tar -zxvf netapp_esx_host_utilities_5_1.tar.gz", then cd into netapp_esx_host_utilities_5_1, then run a "tar -xvf sanlun_bin_netapp.tar" and then cd into opt/netapp/santools and run the mbrscan and mbralign in there.

Re: mbralign 5.2.1 will not align the correct file

support_4
views-count 5848 Views

I've used the old version before too - but it broke the vmdk-files after updating to ESX4.1 and running it from a host on this version.

mbralign 5.2.1 will not align the correct file

brendan80
views-count 5848 Views

Did anyone find a solution to the issue with mbralign V1.4?

Re: mbralign 5.2.1 will not align the correct file

droach
views-count 5848 Views

Anyone find a solution?  I have the same problem with mbralign where I tell it to align a particular VM and it goes off searching through every datastore looking at vmdk files of other machines.  A --scan or --preview finds the VM just fine, but when I remove the --scan or --preview it goes off searching every datastore.

Re: mbralign 5.2.1 will not align the correct file

HSAVELKOUL
views-count 5848 Views

Same problem here also. Scan works fine, but when trying to align the machine it seaches every datastore, then comes up with the message:

The same vmdk was found in multiple vmx files.

Please give explicit path to vmdk file location

This is not the case. the vmdk is only used in one VM.

When I try to specify the explicit path to the vmdk file location it comes up with the same error stated above.

Re: mbralign 5.2.1 will not align the correct file

afgitdepartment
views-count 5848 Views

use the 5.1 tools...i've had no problem with them.

Matt.

mbralign 5.2.1 will not align the correct file

HSAVELKOUL
views-count 5848 Views

I'd rather not do that if it corrupts VMDK files on ESX4.1:

                            support@schur.com                                                            Novice                                                                                   

                                   

                                               

                        May 4, 2011 12:55 AM                            (in response to afgitdepartment)                       

                                                Re: mbralign 5.2.1 will not align the correct file                                           

                                           

I've used the old version before too - but it broke the vmdk-files after updating to ESX4.1 and running it from a host on this version.

Re: mbralign 5.2.1 will not align the correct file

afgitdepartment
views-count 5848 Views

I have not had the problem with 4.1. Make a backup of the vmdk before and try it.

From: HSAVELKOUL

Sent: Thursday, August 11, 2011 08:41 AM

To: Matt Goli

Subject: "mbralign 5.2.1 will not align the correct file"

NetApp Online Community <http://communities.netapp.com/index.jspa>

<http://media.netapp.com/images/divider-600x3.jpg>

Re: mbralign 5.2.1 will not align the correct file

created by HSAVELKOUL <http://communities.netapp.com/people/HSAVELKOUL> in Products & Solutions - View the full discussion <http://communities.netapp.com/message/60716#60716>

<http://media.netapp.com/images/divider-600x3.jpg>

I'd rather not do that if it corrupts VMDK files on ESX4.1:

../people/support%40schur.com/avatar/46.png?a=-1 <mailto:support@schur.com> ../4.5.5/images/status/statusicon-53.gif

support@schur.com

2 posts since

Sep 9, 2008

May 4, 2011 12:55 AM (in response to afgitdepartment <http://communities.netapp.com/14540?tstart=0#53285> )

Re: mbralign 5.2.1 will not align the correct file <http://communities.netapp.com/message/53294#53294>

I've used the old version before too - but it broke the vmdk-files after updating to ESX4.1 and running it from a host on this version.

  1. of replies to the post:

Discussion thread has 8 replies. Click here <http://communities.netapp.com/message/60716#60716> to read all the replies.

Original Post:

I am trying to get mbralign to align one of my WinXP vmdk-files. I can use mbralign --scan "path" and get the message that this vmdk is not aligned. With the machine still be shut down, I remove the --scan from the command, and then it starts trying other vmdk's on the host's VMFS volumes instead of the one I am pointing it to...? Host is ESX4.1u1 Host Utilities are version 5.2.1

Reply to this message by replying to this email -or- go to the message on NetApp Community <http://communities.netapp.com/message/60716#60716>

Start a new discussion in Products & Solutions by email <mailto:message-community-products_and_solutions@netapp-community.hosted.jivesoftware.com> or at NetApp Community <http://communities.netapp.com/choose-container!input.jspa?contentType=1&containerType=14&container=2068>

<http://media.netapp.com/images/divider-600x3.jpg>

Stay Connected: Facebook <http://www.facebook.com/NetApp> Facebook <http://www.facebook.com/NetApp> Twitter <http://twitter.com/NetApp> Twitter <http://twitter.com/NetAppCommunity> LinkedIn <http://www.linkedin.com/groups?about=&gid=111681> LinkedIn <http://www.linkedin.com/groups?about=&gid=111681> YouTube <http://www.youtube.com/user/NetAppTV> YouTube <http://www.youtube.com/user/NetAppTV> Community <http://communities.netapp.com/index.jspa> Community <http://communities.netapp.com/index.jspa>

<http://media.netapp.com/images/divider-600x3.jpg>

Go further, faster<http://media.netapp.com/designimages/tagline-footer.jpg> © 2011 NetApp <http://www.netapp.com/us/site/copyright.html> | Privacy Policy <http://www.netapp.com/us/site/privacy.html> | Unsubscribe <http://communities.netapp.com/user-notification-preferences!input.jspa> | Contact Us <mailto:xdl-communities@netapp.com>

495 E. Java Drive, Sunnyvale, CA 94089 USA

mbralign 5.2.1 will not align the correct file

droach
views-count 5848 Views

The 5.1 version corrupted our templates.  VM's created from them were unbootable after running the 5.1 mbralign tool.  This is a "known" issue with 5.1 mbralign.

mbralign 5.2.1 will not align the correct file

ryanbradley
views-count 5848 Views

Same thing is happening to me. Scan and Preview work ok, but when I run MBRAlign on its own it scans through all datastores.

As a workaround I have moved the VM to be aligned to a local datastore on the ESX Host.

The MBRAlign tool then worked OK.

mbralign 5.2.1 will not align the correct file

HSAVELKOUL
views-count 5848 Views

The workaround to put the VM on the local storage works fine for me too. Unfortunately not all our vm's will fit on local storage

mbralign 5.2.1 will not align the correct file

SIGEPSPAM
views-count 5848 Views

we found the same problem/resolution -- moving the VM to local storage on the temporary ESX (not ESXi) server let us use the v5.2.1 mbralign tool. However -- we ran into issues with large VM's not fitting into the available free space on this local drive. I even tried moving the backup-align files to the SAN datastores, but nothing. I too have a technical support case open with no luck. They actually closed the ticket and tried to pawn me off to Professional Services to pay for them to fix the issue. Whack.

mbralign 5.2.1 will not align the correct file

rodrigon
views-count 5848 Views

For this reason (we ran into issues with large VM's not fitting into the available free space on this local drive.), I installed an ESX 4, put it in ESX cluster and ran mbralign direct on the datastore.

Nasc

NetApp - Enjoy it!

mbralign 5.2.1 will not align the correct file

SIGEPSPAM
views-count 5848 Views

Nasc -- so if I ditch my temporary ESX4.1 server and re-install v4.0 -- will the current version (5.2.1) of mbralign work? I tried finding older versions on the NOW site to no avail. thanks...

G2 Review Banner
All Community Forums
Public