Issue with Powershell results typing in manually vs runnig within script

[JAL]

All,

If I enter the command >Get-NaVol manually in Powershell it list all Volumes on the controller in a chart like view as seen below.

However, if I run the same exact command with a Powershell script (*.ps1).  The results are layed out much differnet as seen in the 2nd example.

Is there a way to run the script to have it display the volume information as in example 1 ?   Thanks for any help.

Joe

Example 1

Name                      State       TotalSize  Used  Available Dedupe  FilesUsed FilesTotal Aggregate
----                      -----       ---------  ----  --------- ------  --------- ---------- ---------
Backup_Vol1        online         4.5 TB   78%  1010.4 GB  True         104        32M aggr1_Sata
Backup_Vol2        online         3.0 TB   49%     1.5 TB  True         104        32M aggr1_Sata
Backup_Vol3        online         5.0 TB   60%     2.0 TB  True         104        32M aggr1_Sata

Example 2

DedupeEnabled                : True
ChecksumStyle                : block
CloneChildren                :
CloneParent                  :
ContainingAggregate          : aggr1
DiskCount                    : 8
FilesTotal                   : 622580
FilesUsed                    : 155
IsChecksumEnabled            : True
IsInconsistent               : False
IsSnaplock                   : False
IsUnrecoverable              : False
MirrorStatus                 : unmirrored
Name                         : testvol
PercentageUsed               : 0
PlexCount                    : 1
Plexes                       : {/aggr1/plex0}
QuotaInit                    : 0
RaidSize                     : 16
RaidStatus                   : raid_dp,sis
Reserve                      : 0
ReserveRequired              : 0
ReserveUsed                  : 0
Sis                          : idle
SizeAvailable                : 17175904256
SizeTotal                    : 17179869184
SizeUsed                     : 3964928
SnaplockType                 :
SpaceReserve                 : volume
SpaceReserveEnabled          : True
State                        : online
Type                         : flex
Uuid                         :cklfdjcpowe-dclnsdnkc=ckda
IsUnrecoverableSpecified     : True
PercentageUsedSpecified      : True
SpaceReserveEnabledSpecified : True

[JGPSHNTAP]

Thats because get-navol uses default templates on the output.xml

what's your PS1.. please post it

[JAL]

Thanks for the reply.  The script is still being written for what I want it to accomplish but, here are the lines in the script that I'm using currently.

    $Filer = $(Read-Host -prompt "On which NetApp filer are you creating the LunClone?")
    
Connect-NaController $Filer -credential (Get-Credential) -HTTPS
Get-NaVol
Get-NaLun

My end game is to present the user running the script the table format of the Volumes and Luns on the stated controller to answer the next group of questions the script will ask the user.

What is listed above works fine other than the way it displays the volume and lun information.

Thanks,

Joe

[asulliva · Accepted solution]

Have you tried simply piping to Format-Table?

$Filer = $(Read-Host -prompt "On which NetApp filer are you creating the LunClone?")
    
Connect-NaController $Filer -credential (Get-Credential) -HTTPS
Get-NaVol | Format-Table
Get-NaLun | Format-Table

[JAL]

Asulliva,

Sweet!  thanks for the reply.  That did the trick. Exactly what I was looking to accomplish.

Thanks again,

I'm still learning Powershell and it's syntax and possibilities so, didn't even think to use that cmdlet for the output.

Joe