The syntax is: Set-NcQtree /vol/vol1/qtree1 -SecurityStyle ntfs -EnableOplocks -VserverContext vserver_1 Or you can replace -EnableOplocks with -DisableOplocks ... View more

Hi Rolf, 4.2.1 I believe is the latest release and still does not support Windows 2012. ... View more

haha good tip, thanks Scott, luckily we usually use CLI or Powershell ... View more

thanks Scott I believe you are right, we are using LS-Mirrors on all our root drives for vservers. That makes sense, I overlooked that componenet. ... View more

Hi, I just came across the same issue. I ran a manual poll with the option to rebuild ETL and the status changed to Success. Did you try a manual poll ? ... View more

thanks for your reply, so based on your schedule 1 dedupe job can not run for more than 2 minutes ? Is that a bit of a nightmare to administer a schedule for 400 volumes ? There must be a setting somewhere that will limit the amount of concurrent dedupe job running, that way just use the default midnight schedule and let the system work out the queues. ... View more

Hi you can use: statistics start statistics show -object nfs* When you are finished - statistics stop ... View more

Hi Mark you'll need to use snapmirror show -fields destination-volume ... View more

Hi good to see you worked it out, sorry I had not found time to look into your logs. I actually seen other weird issues with enabling jumbo frames with the sim and in workstation. When running on vm workstation, like you mentioned above, don't use jumbo frames. ... View more

When you provisioned the simulator did you right click the *.vmx file and select open with VMware Workstation ? I can't look at the log files now but will today or tomorrow ... View more

what version of workstation are you using and can you attach the vmware log file ... View more

yes, we use that it gives us a look into performance but does not let us schedule reports to be emailed out ... View more

Hi Riley, I've tried to enable the performance reports via the cli with the -p option however it says this is not supported in clustered mode ... View more

Hi Scott, thanks Yes I will add "Use at your own risk" The vreport method, is this only if c-mode cannot see the 7-mode aggregate on the disks ? ... View more

Exactly, purely transitioning though you can still setup a schedule to constantly update the snapmirror until you are ready to cut over, not to be confused with setting up a snapmirror and leaving it running for DR ... View more

Actually, I believe it is supported as it comes straight from the netapp support site for transitioning https://library.netapp.com/ecmdocs/ECMP1213598/html/index.html (Under transitioning volumes manually) ... View more

Hi, we are replicating between 7-mode system and cluster mode system, you cannot go the other way though. You need to make sure that your snapmirror is type TDP and you need to setup a peer relationship. I've created a tutorial on my blog to high light the steps involved along with a few Gotcha's that i've come across: http://www.sysadmintutorials.com/tutorials/netapp/netapp-clustered-ontap/netapp-snapmirror-7-mode-to-cluster-mode/ ... View more

Hi Emanuele, further to my previous comment today I have the resolution for you. It is possible to delete a 7-mode aggregate from within a c-mode system. I've written up a tutorial on the full process in my blog: http://www.sysadmintutorials.com/tutorials/netapp/netapp-clustered-ontap/netapp-7-mode-shelf-connected-to-cluster-mode-system/ ... View more

Hi we are having the same issue, The old 7-mode system had been shut off and disk shelves unplugged. When connected into the c-mode system I could still see the disk ownership as the 7-mode system. I'm able to reassign the disks to a new c-mode node however it see's the old aggregate. I can't change state to spare as it says: Error: command failed: Failed to unfail the disk. Reason: Disk is not currently        failed. I can't change the state to failed as it says: disk fail: Cannot fail disk (volume/plex is offline). Any other ideas ? ... View more

So the setup is now vCenter running on Windows 2012 and a separate Server running Windows 2008 for VSC. This is working perfectly. ... View more